RECALLS — MACK CHU
Mack CHU recalls
Mack CHU model years 2010–2017 covered by at least one recall campaign. Pick a year to see the Canadian and U.S. campaigns side by side.
Choose a model year
U.S. NHTSA campaigns are listed on each year page, where they are queried live by model year. The Canadian list below covers every year together.
Transport Canada recalls
25- Steering#2017426
38 units affected
On certain vehicles, the castellated nut and cotter pin on the steer axle may not have been tightened to specification. This could cause the tie rod to become loose in the steer axle, which would result in audible noise and/or looseness in steering. If the vehicle were continued to be operated in this condition, the tie rod could disconnect from the knuckle, resulting in a complete loss of control of a vehicle wheel, which would increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the torque of the castellated nuts on the tie rod, and replace the tie rod stud and knuckle as necessary.
- Steering#2016642
43 units affected
On certain vehicles, the front hubs do not support the gross axle weight rating of the front axle. Specifically, 5,987 Kg (13,200 lbs.) rated front hubs were used on trucks requiring a 6,622 Kg (14,600 lbs.) rated front axle. If the axle load exceeds the maximum weight capacity of the hub, there is an increased risk of hub and bearing failure, which could cause a complete separation of the wheel(s) and a loss of vehicle control, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the front hub assemblies with hub assemblies rated for 6,622 Kg (14,600 lbs). Note: If damage occurs due to overloading, the ABS Malfunction light may illuminate as the distance between the ABS tone ring and the sensor increases (i.e. sensor loses contact with the tone ring).
- Powertrain#2016495
1,690 units affected
On certain vehicles, the cap nut that retains the interaxle driveshaft yoke to the rear axle input shaft may prematurely loosen. If the nut were to loosen and come off, the yoke could separate from the axle input shaft and cause the drive shaft to disconnect. A disconnected drive shaft would result in a loss of motive power, and create a road hazard, both of which could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the torque on the cap nut, and the nut will be replaced if the torque is found under specification. Note: This is an expansion of recall 2016-079.
- Powertrain#2016079
1,068 units affected
On certain vehicles, the cap nut that retains the interaxle driveshaft yoke to the rear axle input shaft may prematurely loosen. If the nut were to loosen and come off, the yoke could separate from the axle input shaft and cause the drive shaft to disconnect. A disconnected drive shaft would result in a loss of motive power, and create a road hazard, both of which could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the cap nut, and inspect the threads on the input shaft. If the threads are damaged, the input shaft will be replaced.
- Structure#2015457
4 units affected
On certain vehicles, the fifth wheel locking mechanisms could be susceptible to damage and/or wear. This could cause the locking mechanism to fail properly engage, potentially resulting in a towed trailer unit separating from the truck tractor. As a result, the trailer could strike another vehicle, stationary object, or bystander, causing injury and/or damage to property. Correction: Fontaine dealers will replace all Ultra LT fifth wheel units with Ultra NT model fifth wheel units.
- Brakes#2015372
241 units affected
On certain vehicles, The chassis electrical harness and air brake lines may not have been properly secured at the crossmember. This could cause the electrical cables and air lines to fall down and get twisted in the driveline. This could affect safety systems such as brakes, increasing stopping distances or causing unintended parking brake application. This could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect and repair the vehicle as needed.
- Accessories#2015100
71 units affected
On certain vehicles, the fifth wheel remote unlocking switch may not work as designed. As a result, the driver may inadvertently release the 5th wheel latch when the park brake is applied if he/she presses or bumps the switch. This could cause the trailer to decouple from the truck increasing the risk of injury and/or damage to property. Correction: Dealers will add a redundant measure such as an additional switch or adding a thumb lock that requires 2 actions to push the switch.
- Electrical#2015017
32 units affected
On certain model vehicles outfitted with an Automatic Over-Speed Protection system, the system may be incorrectly wired. This presents a potential risk as the operator may not be able to control an unintended increase in the engine RPM if combustible vapors enter through the air intake. If this occurs, it could increase the risk of an engine fire that may cause injury and/or property damage. Correction: Dealers will inspect and repair accordingly.
- Electrical#2014527
11,668 units affected
On certain model vehicles, water around the windshield can migrate into the Electronic Power Distribution Module and contaminate it. As a result, circuits may be bridged creating an electrical short. This could potentially result in a fire, increasing the risk of injury and/or damage to property. Correction: Dealers will inspect the module, and if found contaminated, will replace it. Additional measures will be taken to address the leak if contamination is found. Note: This is an expansion of recall 2014-053.
- Suspension#2014526
33 units affected
On certain vehicles, the collars that prevent the ball sockets from backing out of the tie rod may have been incorrectly positioned. If the ball socket(s) became loose, a complete loss of steering or loss of steering at one wheel end could occur, which could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect, and if necessary, reposition the collar.
- Seats And Restraints#2014390
46 units affected
On certain vehicles, bolts securing the seat belts to the seat frame, cab wall and cab floor may have been insufficiently tightened during vehicle assembly. As a result, bolts could loosen over time and potentially allow the seat belt to detach from its mounting points. If this occurs, the seat belt may fail to restrain the seat occupant in a crash, increasing the risk of injury and/or damage to property. Correction: Dealers will tighten the affected bolts to the specified torque.
- Lights And Instruments#2014146
5,990 units affected
On certain vehicles, the directional/hazard signal flasher may fail. Actuation of the turn signal or hazard lights in this condition would cause them to remain illuminated and not flash as intended. As a result, drivers may not be able to clearly signal their intentions to turn, change lanes or warn others in an emergency situation. Correction: Dealers will replace the turn signal/hazard flasher module.
- Electrical#2014053
2,462 units affected
On certain model vehicles, water around the windshield can migrate into the Electronic Power Distribution Module and contaminate it. As a result, circuits may be bridged creating an electrical short. This could potentially result in a fire, increasing the risk of injury and/or damage to property. Correction: Dealers will inspect the module, and if found contaminated, will replace it. Additional measures will be taken to address the leak if contamination is found.
- Accessories#2013454
12 units affected
On certain model vehicles outfitted with an Automatic Over-Speed Protection system, the system may be incorrectly wired. This presents a potential risk in applications where the Power Take-Off system is engaged, which could result in injury and/or property damage. Correction: Dealers will rewire the system.
- Powertrain#2013346
61 units affected
On certain vehicles, spindle nuts may have been installed incorrectly and could loosen, possibly resulting in the hub, wheel and tire assembly separating from the vehicle. This could increase the risk of a crash causing injury and/or property damage. Also, should a wheel separate from the vehicle, it could pose a danger to nearby motorists or bystanders, which could result in injury and/or property damage. Correction: Dealers will inspect and repair vehicles as required.
- Brakes#2013161
906 units affected
On certain trucks, the cotter pin which retains the brake slack adjuster’s clevis pin may have been omitted during vehicle assembly. As a result, the clevis pin could loosen and fall out, causing a loss of brake function at the affected wheel. This could cause the vehicle to pull to one side under braking, or increase stopping distance, which could result in a crash causing property damage and/or personal injury. Correction: Dealers will verify cotter pin installation on each brake slack adjuster. Replacement cotter pins and/or clevis pins will be installed as needed.
- Wheels#2012346
On certain vehicles, the wheel rims may have been manufactured incorrectly and could fail. A wheel separating from the vehicle could cause a loss of control and a crash. In addition, the errant wheel assembly could strike a vehicle, stationary object, or a bystander. These issues could result in property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the wheel rims. Note: Further evaluation revealed that no Canadian vehicles are involved.
- Lights And Instruments#2012300
1,168 units affected
On certain trucks, an electrical short circuit in the fog light circuitry could result in a loss of low beam headlamp function. Loss of headlamp illumination, should it occur during a rainy/snowy day, or during hours of darkness, could compromise the driver’s ability to see the road and its users, which could result in a crash causing property damage and/or personal injury. Correction: Dealers will add an extra wiring harness between the cab harness and the Daytime Running Lamp (DRL) module, in order to isolate the fog light circuit.
- Visual System#2012194
66 units affected
On certain vehicles, the hardware used to affix the windshield wiper linkage to the wiper motor may have been subject to rust and corrosion before assembly. This contamination may have prevented the bolt/nut from being tightened adequately. As a result, the bolt/nut may loosen to a point where the linkage detaches from the wiper motor, which would cause the wipers to stop functioning. Loss of windshield wiping capability, should it occur during a rainy/snowy day, may compromise the driver's ability to see the road and its users, which could result in a crash causing property damage and/or personal injury. Correction: Dealers will replace the hardware in question.
- Brakes#2012033
9 units affected
On certain trucks equipped with Bendix ATR-6 Antilock Traction Relay valves, in extremely cold conditions (at or below -18 degrees Celsius), internal ATR valve leakage can occur. This could cause unintended brake application, which could overheat the affected brakes and cause a fire. Also, in certain low traction conditions, unexpected brake application can cause a loss of vehicle control and a crash. These issues could result in property damage and/or personal injury. Correction: Dealers will update the cover assembly on the ATR valves.
- Other#2011261
76 units affected
On certain trucks, the clutch pedal assembly may have been manufactured incorrectly and could fail. This could allow the clutch pedal to fall to the floor, prohibiting clutch operation, and causing a reduction in braking efficiency. Increased stopping distances could result in a crash causing property damage and/or personal injury. Correction: Dealers will replace the clutch pedal assembly.
- Powertrain#2011205
584 units affected
On certain trucks, the driveshaft may not have been welded correctly during the manufacturing process. This could allow the driveshaft to fracture along the length of the tube seam weld when torque is applied. The fractured tube can twist or sever, which could result in additional damage to the driveline, the vehicle to which it is attached, and any additional nearby components. Should the brake air lines become damaged, it could allow spring brake application, causing immediate brake lock-up. If this occurs while the vehicle is in motion, it could result in a crash. Also, failure of the driveshaft would result in lost vehicle propulsion which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash. Either condition could result in property damage and/or personal injury. Correction: Dealers will replace the driveshaft assembly.
- Brakes#2011182
329 units affected
On certain vehicles, the slack adjuster housings may have been manufactured incorrectly, which could allow the housings to fracture and fail. As a result, the wheel brake to which the slack adjuster is attached would no longer function, which could increase vehicle stopping distances. Should a steer axle slack adjuster fail, it could also cause the vehicle to pull to one side during braking. Either problem could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the slack adjusters.
- Other#2011146
42 units affected
On certain trucks, the bolts used to secure the fifth wheel hitch assembly to the frame may not have received adequate tightening torque during vehicle assembly. This could allow the mounting bolts to fail and the fifth wheel assembly, as well as the trailer, to separate from the tractor. A towed unit separating from the towing vehicle could strike another vehicle, stationary object, or bystander, causing property damage and/or personal injury. Correction: Dealers will inspect the mounting bolts and replace as required.
- Visual System#2010371
3 units affected
On certain vehicles, the rear conspicuity reflector typically found on the mud flap hanger brackets may not have been installed in the back of the cab which is the alternate position allowed for vehicle manufactured without mud flap hanger brackets. Missing reflector is a non-compliance with Canada Motor Vehicle Safety Standards 108 - Ligthing System and Retroreflective Devices. Correction: Dealers will inspect and if missing will install the required reflectors.
Canadian data updated August 24, 2026
Does this recall apply to my vehicle?
Matched by make, model, and model year. Many recalls affect only specific VIN ranges — confirm with your dealer using your full VIN.
What to do
Recall repairs are free at a franchised dealer in both countries. To confirm a recall applies to your specific vehicle, contact your manufacturer or dealer with your full VIN, or use the official channel:
- NHTSA recall lookup (search by VIN) — U.S. National Highway Traffic Safety Administration
- Defects and recalls database — Transport Canada