2013 Mack CHU recalls

• Steering#2016642December 20, 2016

  43 units affected

  On certain vehicles, the front hubs do not support the gross axle weight rating of the front axle. Specifically, 5,987 Kg (13,200 lbs.) rated front hubs were used on trucks requiring a 6,622 Kg (14,600 lbs.) rated front axle. If the axle load exceeds the maximum weight capacity of the hub, there is an increased risk of hub and bearing failure, which could cause a complete separation of the wheel(s) and a loss of vehicle control, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the front hub assemblies with hub assemblies rated for 6,622 Kg (14,600 lbs). Note: If damage occurs due to overloading, the ABS Malfunction light may illuminate as the distance between the ABS tone ring and the sensor increases (i.e. sensor loses contact with the tone ring).

• Powertrain#2016495October 11, 2016

  1,690 units affected

  On certain vehicles, the cap nut that retains the interaxle driveshaft yoke to the rear axle input shaft may prematurely loosen. If the nut were to loosen and come off, the yoke could separate from the axle input shaft and cause the drive shaft to disconnect. A disconnected drive shaft would result in a loss of motive power, and create a road hazard, both of which could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the torque on the cap nut, and the nut will be replaced if the torque is found under specification. Note: This is an expansion of recall 2016-079.

• Powertrain#2016079February 18, 2016

  1,068 units affected

  On certain vehicles, the cap nut that retains the interaxle driveshaft yoke to the rear axle input shaft may prematurely loosen. If the nut were to loosen and come off, the yoke could separate from the axle input shaft and cause the drive shaft to disconnect. A disconnected drive shaft would result in a loss of motive power, and create a road hazard, both of which could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the cap nut, and inspect the threads on the input shaft. If the threads are damaged, the input shaft will be replaced.

• Structure#2015457October 8, 2015

  4 units affected

  On certain vehicles, the fifth wheel locking mechanisms could be susceptible to damage and/or wear. This could cause the locking mechanism to fail properly engage, potentially resulting in a towed trailer unit separating from the truck tractor. As a result, the trailer could strike another vehicle, stationary object, or bystander, causing injury and/or damage to property. Correction: Fontaine dealers will replace all Ultra LT fifth wheel units with Ultra NT model fifth wheel units.

• Brakes#2015372August 17, 2015

  241 units affected

  On certain vehicles, The chassis electrical harness and air brake lines may not have been properly secured at the crossmember. This could cause the electrical cables and air lines to fall down and get twisted in the driveline. This could affect safety systems such as brakes, increasing stopping distances or causing unintended parking brake application. This could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect and repair the vehicle as needed.

• Accessories#2015100March 10, 2015

  71 units affected

  On certain vehicles, the fifth wheel remote unlocking switch may not work as designed. As a result, the driver may inadvertently release the 5th wheel latch when the park brake is applied if he/she presses or bumps the switch. This could cause the trailer to decouple from the truck increasing the risk of injury and/or damage to property. Correction: Dealers will add a redundant measure such as an additional switch or adding a thumb lock that requires 2 actions to push the switch.

• Electrical#2014527November 20, 2014

  11,668 units affected

  On certain model vehicles, water around the windshield can migrate into the Electronic Power Distribution Module and contaminate it. As a result, circuits may be bridged creating an electrical short. This could potentially result in a fire, increasing the risk of injury and/or damage to property. Correction: Dealers will inspect the module, and if found contaminated, will replace it. Additional measures will be taken to address the leak if contamination is found. Note: This is an expansion of recall 2014-053.

• Lights And Instruments#2014146April 22, 2014

  5,990 units affected

  On certain vehicles, the directional/hazard signal flasher may fail. Actuation of the turn signal or hazard lights in this condition would cause them to remain illuminated and not flash as intended. As a result, drivers may not be able to clearly signal their intentions to turn, change lanes or warn others in an emergency situation. Correction: Dealers will replace the turn signal/hazard flasher module.

• Powertrain#2013346October 7, 2013

  61 units affected

  On certain vehicles, spindle nuts may have been installed incorrectly and could loosen, possibly resulting in the hub, wheel and tire assembly separating from the vehicle. This could increase the risk of a crash causing injury and/or property damage. Also, should a wheel separate from the vehicle, it could pose a danger to nearby motorists or bystanders, which could result in injury and/or property damage. Correction: Dealers will inspect and repair vehicles as required.

• Brakes#2013161May 10, 2013

  906 units affected

  On certain trucks, the cotter pin which retains the brake slack adjuster’s clevis pin may have been omitted during vehicle assembly. As a result, the clevis pin could loosen and fall out, causing a loss of brake function at the affected wheel. This could cause the vehicle to pull to one side under braking, or increase stopping distance, which could result in a crash causing property damage and/or personal injury. Correction: Dealers will verify cotter pin installation on each brake slack adjuster. Replacement cotter pins and/or clevis pins will be installed as needed.

• Wheels#2012346October 11, 2012

  On certain vehicles, the wheel rims may have been manufactured incorrectly and could fail. A wheel separating from the vehicle could cause a loss of control and a crash. In addition, the errant wheel assembly could strike a vehicle, stationary object, or a bystander. These issues could result in property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the wheel rims. Note: Further evaluation revealed that no Canadian vehicles are involved.

Canadian data updated August 24, 2026

• EXTERIOR LIGHTING:TURN SIGNAL:FLASHER UNIT#14V208000April 18, 2014

  Mack Trucks Inc. (Mack) is recalling certain model year 2010-2014 CHU, CXU, and MRU, 2007 CT and CV, 2008-2014 GU, and 2011-2014 LEU, and TD trucks manufactured February 28, 2006, through November 8, 2013, and equipped Hamsar Electronic Flasher. The hazard warning lights may fail.

  Risk: A failure of the hazard warning lights could reduce the trucks visibility, increasing the risk of a crash.

  Remedy: Mack will notify owners, and dealers will replace the electronic flasher unit, free of charge. The recall will begin by mid-June 2014. Interim letters went out to owners on June 23, 2014. The recall began on July 25, 2014. Owners may contact Mack customer service at 1-866-298-6586. Mack's number for this recall is SC0379.

• ELECTRICAL SYSTEM#14V078000February 21, 2014

  Mack Trucks, Inc. (Mack) notified the agency on February 20, 2014, that they are recalling certain model year 2010-2012 CHU, CXU, GU and TD vehicles manufactured from June 16, 2009, through July 8, 2011. While continuing to research the scope of the issue, Mack expanded the recall on November 18, 2014 to include certain model year 2008-2009 and 2013-2014 CHU, CXU, GU and TD vehicles manufactured from June 16, 2009, through July 8, 2011. Having completed its investigation, Mack once again expanded the recall during February 2015 to include an additional 53,780 vehicles from model years 2007 and 2015. The recall now covers model year 2007-2015 includes CHU, CXU, GU and TD vehicles produced October 13, 2006, through October 3, 2014. In the affected vehicles, the Electronic Power Distribution Module (EPDM) may be contaminated from water leaks in, and around, the windshield. If exposed to water leaks, contaminants such as road salts may deposit on the EPDM.

  Risk: Deposits of contaminants may result in the circuits being bridged, creating a high resistance short, increasing the risk of a fire.

  Remedy: Mack has notified owners, and dealers will inspect the EPDM. If contamination has occurred, dealers will replace the EPDM and address the leak, free of charge. Owners of model year 2010-2012 CHU, CXU, GU and TD vehicles were initially notified April 24, 2014. Owners affected by the recall expansions were notified in February 2015. Owners may contact Mack Trucks at 1-336-393-2000. Mack's number for this recall is SC0375.

• POWER TRAIN:AXLE HUBS#13V492000October 17, 2013

  Mack Trucks is recalling certain model year 2013-2014 CHU, CXU, GU, LEU, and MRU vehicles manufactured with pro-torque axle spindle nuts from August 28, 2012, through August 16, 2013. The pro-torque nut may not have been installed correctly, which may result in a loosening of the nut.

  Risk: If the nut comes loose, the hub assembly may separate from the vehicle, increasing the risk of a crash.

  Remedy: Mack Trucks will notify owners, and dealers will inspect and repair the vehicles, as necessary, free of charge. The recall began on November 12, 2013. Mack's recall number is SC0371. Owners may contact Mack Trucks at 1-336-393-2000.

• SERVICE BRAKES#13V195000May 13, 2013

  Mack Trucks, Inc. is recalling certain model year 2013-2014 CHU, CXU, GU, MRU, and LEU trucks manufactured July 16, 2012, through march 18, 2013 and equipped with drum brakes. The clevis pin for the brake slack adjuster may be missing a cotter pin. If the cotter pin is not installed, the clevis pin may loosen and fall out causing a loss of brake function on the affected wheel.

  Risk: A loss of brake function at one wheel will lead to increased stopping distances and pulling to the left or right when braking, which may increase the risk of a crash.

  Remedy: Mack Trucks, Inc. will notify owners, and dealers will inspect the brake slack adjusters and install the brake hardware, as necessary, free of charge. An interim was mailed to owners on June 20, 2013. A second notice was mailed to owners on September 30, 2013. Owners may contact Mack Trucks at 1-800-528-6586. Mack Trucks' recall campaign number is SC0370.