2016 Kenworth T660 recalls

• Lights And Instruments#2020148April 7, 2020

  65,284 units affected

  Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).

• Electrical#2018442August 23, 2018

  4,186 units affected

  On certain trucks with an ISX15 engine and a 1.9 M cab, the engine wiring harness is missing circuits to allow the illumination of Check (CEL) and Stop (SEL) Engine Lamps and sounding of the Stop Engine Alarm. A failure to notify the operator of a serious engine problem may result in an engine failure without warning, and loss of motive power while the vehicle is in motion, which could increase the risk of a crash causing injury and/or property damage. Correction: Dealers will inspect and/or test the engine harness for the missing circuits, and if found missing, an overlay jumper harness will be installed.

• Brakes#2018389July 24, 2018

  214 units affected

  Certain vehicles may fail to conform to the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 121 - Air Brake Systems and CMVSS 136 - Electronic Stability Control Systems for Heavy Vehicles. In the event that the anti-lock brake system (ABS) loses battery and/or ignition power to the controller, the ABS indicator lamp may not illuminate to warn the driver of the loss of ABS, which is contrary to the requirements of the standards. This could result in the loss of ABS function with no warning to the driver, which could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will reprogram the cab control module.

• Steering#2017461September 25, 2017

  281 units affected

  On certain vehicles, the castellated nut and cotter pin on the steer axle may not have been tightened to specification. This could cause the tie rod to become loose in the steer axle, which would result in audible noise and/or looseness in steering. If the vehicle were continued to be operated in this condition, the tie rod could disconnect from the knuckle, resulting in a complete loss of control of a vehicle wheel, which would increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the torque of the castellated nuts on the tie rod, and replace the tie rod stud and knuckle as necessary.

• Engine#2015418September 23, 2015

  9 units affected

  On certain vehicles equipped with a Cummins engine, the Engine Control Module (ECM) could develop an internal electrical short circuit that could blow a fuse in the ECM’s electrical supply circuit. This could result in an unexpected engine stall without the ability to restart the engine, which could increase the risk of a crash. Correction: Dealers will replacing the existing, affected ECM with a new ECM.

• Brakes#2015318July 20, 2015

  32 units affected

  Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 121 - Air Brake Systems. The two service brake connections of the SR-7 spring brake valve assembly that provide the valve with feedback from the primary and secondary service brake applications may have been reversed during installation. Although the SR-7 valve would still function properly if there were normal reservoir pressure, in the event of a failure in the primary or secondary circuit, the redundant circuit would not provide adequate service brake functionality, and the vehicle would fail to meet the emergency brake system performance standard. This could result in reduced braking performance which could result in a vehicle crash. Correction: Dealers will inspect, remove and reconnect the air lines to the correct port of the SR-7 valve.

• Lights And Instruments#2015316July 20, 2015

  4,791 units affected

  Certain vehicles equipped with HID headlamps may not comply with the requirements of Canada Motor Vehicle Safety Standard 108 - Lighting System and Retroreflective Devices. A Daytime Running Lamp (DRL) that is optically combined with a turn signal lamp must switch off when the turn signal lamp is switched on as a hazard warning signal. In the affected vehicles, the DRL overrides the hazard flashing functionality after the service brake is applied for more than 2 seconds, which is contrary to the standard. The hazard functionality returns to normal when the application of the service brake is removed. Turn signal functionality would not impacted. Failure to warn oncoming vehicles with flashing hazard lamps could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will update vehicle software.

• Electrical#2015190May 8, 2015

  22,815 units affected

  On certain vehicles, water could migrate into wiper motor head and could lead to internal corrosion. This internal corrosion could form a conductive salt bridge which could result in a short circuit, causing the wiper system to fail. Loss of windshield wiping capability, should it occur during a rainy/snowy day, may compromise the driver's ability to see the road and its users, and a short circuit could increase the risk of fire, which could result in injury and/or damage to property. Correction: Dealers will install a shield over the wiper motor to protect it from water intrusions and prevent corrosion.

• Electrical#2015189May 8, 2015

  140 units affected

  On certain vehicles equipped with PACCAR MX-13 engines and Delco-Remy 40SI alternators, the alternator charge cable may chafe against an air conditioning discharge line. This chafing could lead to damage of the alternator cable's insulation and could lead to an electrical short, increasing the risk of fire, which could result in injury and/or damage to property. Correction: Dealers will rotate the alternator cable end 180 degrees to provide necessary clearance and reattach the cable to the alternator.

• Wheels#2015188May 8, 2015

  3 units affected

  On certain vehicles, the wheel nuts may have been insufficiently tightened during vehicle assembly. This could cause the wheel nuts to loosen and could lead to a complete separation of the wheel(s) from the vehicle, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect, and properly tighten the lug nuts to specification.

Canadian data updated August 24, 2026

• ELECTRONIC STABILITY CONTROL (ESC)#20V199000April 6, 2020

  PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

  Risk: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

• ENGINE AND ENGINE COOLING:ENGINE:DIESEL#18V555000August 22, 2018

  PACCAR Incorporated (PACCAR) is recalling certain 2016-2019 Kenworth C500, T660, T800, and W900 vehicles, equipped with 1.9M ISX15 engines. The engine harnesses may have been manufactured without check engine light (CEL) and stop engine light (SEL) circuits, preventing the driver from being warned of a serious engine problem.

  Risk: If the driver is not warned of a serious engine problem, the engine may unexpectedly fail, increasing the risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will inspect or test the ISX15 engine harness, and install an overlay jumper harness to supply the missing CEL and SEL circuits, free of charge. The recall began November 30, 2018. Owners may contact PACCAR customer service at 1-918-259-3258. PACCAR's number for this recall is 18KWE.

• ELECTRONIC STABILITY CONTROL (ESC)#18V368000June 1, 2018

  PACCAR Incorporated (PACCAR) is recalling certain 2017-2018 Peterbilt 567 and 579 trucks and 2015-2018 Kenworth T660, T680, T800, T880 and W900 trucks. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

  Risk: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on July 30, 2018. Owners may contact Peterbilt customer service at 1-918-259-3258 or Kenworth customer service at 1-425-828-5000.

• STEERING:LINKAGES:TIE ROD ASSEMBLY#17V593000September 22, 2017

  PACCAR Incorporated (PACCAR) is recalling certain 2016 Peterbilt 220, 320, 325, 330, 337, 348, 365, 367, 382, 384, 386, 389, 389G, 567, 579 and 587 trucks and Kenworth K170, T170, T270, T370, T440, T470,T660, T680, T800, T880, and W900 trucks equipped with certain Spicer D or E series steer axles. The castellated nut on the steer axles may not be properly torqued, allowing the tie rod to loosen.

  Risk: If the tie rod loosens, it may disconnect from the steering knuckle, causing a complete loss of steering and increasing the risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will inspect the torque of the castellated nut and tie rod, tightening it as necessary. If the tie rod stud and knuckle on units cannot be sufficiently torqued, the dealer will replace the knuckle and tie rod end assembly, free of charge. The recall began on November 13, 2017. Owners may contact Peterbilt customer service at 1-940-591-4000 or Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is P817-C.

• ELECTRICAL SYSTEM:IGNITION:MODULE#15V597000September 24, 2015

  Paccar Incorporated (Paccar) is recalling certain model year 2016 Kenworth T370, T660, T680, T800, T880, and W900 vehicles manufactured July 31, 2015, to August 12, 2015, and 2016 Peterbilt 337, 348, 365, 367, 382, 386, 389, 567, 579, and 587 vehicles manufactured August 4, 2015, to August 12, 2015. In the affected vehicles, the Engine Control Module (ECM) may short circuit, causing the engine to stall without warning.

  Risk: An engine that stalls without warning increases the risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will replace the defective engine control modules, free of charge. The recall began on October 22, 2015. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. Paccar's numbers for this recall are 15KWM (Kenworth) and 915-L (Peterbilt).

• SERVICE BRAKES, AIR#15V457000July 22, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2016 Kenworth T440, T470, T660, T680, T800, T880, and W900 trucks manufactured February 16, 2015, to March 9, 2015. The affected vehicles are equipped with an SR-7 spring brake valve assembly that may have had the primary and secondary service brake applications installed in reverse. In the event of a failure in the primary or secondary circuit, the redundant circuit would not provide adequate service brake functionality. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 121, "Air Brake Systems."

  Risk: A loss of braking ability would increase the risk of a crash.

  Remedy: Kenworth will notify owners, and dealers will inspect the vehicles and correct the air line installations as required, free of charge. The recall began on September 16, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 15KWK.

• EXTERIOR LIGHTING:HAZARD FLASHING WARNING LIGHTS#15V458000July 22, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2011-2016 Kenworth T440, T470, T660, T680, and T880 trucks manufactured January 14, 2010, to May 22, 2015, and equipped with HID Headlamps and the option for Daytime Running Lamps (DRL). The DRLs are required to deactivate when the hazard warning lights are activated, however, the DRLs on these vehicles override the hazard flashing functionality after the brake pedal is pushed for more than two seconds. Normal hazard flashing functionality returns once the service brake is released. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, Reflective Devices, and Associated Equipment."

  Risk: If the hazard warning lamps are overridden by the DRL, oncoming vehicles may fail to be warned, increasing the risk of a crash.

  Remedy: Kenworth will notify owners, and dealers will update the cab controller software, free of charge. The recall began on September 167, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. Kenworth's number for this recall is 15KWL.

• WHEELS:LUGS/NUTS/BOLTS/STUDS#15V272000May 11, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2016 Kenworth T660, T680, T800, T880, and W900 trucks manufactured February 1, 2015, to April 20, 2015. During assembly, the affected vehicles did not undergo the rear wheel mounting torque verification process, and thus the rear wheels may be loose.

  Risk: If the rear wheel lug nuts are undertorqued, the wheels may separate from the vehicle, increasing the risk of a crash.

  Remedy: Kenworth will notify owners, and dealers will verify that the rear wheel lug nuts are correctly tightened, free of charge. The recall began on July 1, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. Kenworth's number for this recall is 15KWG.

• VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR#15V271000May 8, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2011-2016 Kenworth T270, T370, T440, T470, C500, C540, C550, T660, T800, W900, and 963 trucks manufactured November 1, 2010, to April 6, 2015. In the affected trucks, water may leak into the wiper motor.

  Risk: As water leaks in, the wiper may cease to function on the 'intermittent' setting, reducing the driver's visibility and increasing the risk of a crash. Additionally, the water may cause corrosion which, over time, may result in an electrical short, increasing the risk of a fire.

  Remedy: PACCAR is still developing and testing a remedy. The recall is expected to begin in July 2015. An interim letter was sent to owners on July 2, 2015. The recall began on September 2, 1015. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 15KWF.

• ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR#15V270000May 8, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2014-2016 Kenworth T660, T680, T880 trucks manufactured February 18, 2013, to April 10, 2015, and 2011-2016 Peterbilt 386, 389, 567, 579, and 587 trucks manufactured December 13, 2010, to April 20, 2015. The affected trucks, equipped with PACCAR MX-13 engines and Delco-Remy 40SI alternators, have alternator charge cables that may chafe against a formed metal freon discharge line.

  Risk: If the alternator cable rubs through its insulation, an electrical short may occur, increasing the risk of a fire.

  Remedy: PACCAR will notify owners, and dealers will reroute the alternator charge cable away from the metal freon line, free of charge. PACCAR issued an interim notification to owners on July 10, 2015. The recall began on September 16, 2015. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. PACCAR's numbers for this recall are 15KWE and 515-F.