Does the 2013 Mitsubishi RVR have any recalls?

Transport Canada lists 9 campaigns and the U.S. NHTSA lists 0 for the 2013 Mitsubishi RVR. Matched by make, model, and model year. Many recalls affect only specific VIN ranges — confirm with your dealer using your full VIN.

How do I know if a recall applies to my 2013 Mitsubishi RVR?

Recalls are matched by make, model and model year, but many cover only certain VIN ranges. Confirm with your manufacturer or dealer using your full VIN, or use the official Transport Canada or NHTSA lookup.

Are recall repairs free?

Yes. In both Canada and the United States the manufacturer must fix a recalled defect at no charge, through a franchised dealer.

RECALLS — MAKE · MODEL · YEAR

2013 Mitsubishi RVR recalls

9 safety recall campaigns have been filed for the 2013 Mitsubishi RVR with Transport Canada and the U.S. NHTSA. Here is what both agencies say.

Canadian recalls: 09
U.S. recalls: 00
Total campaigns: 09

Transport Canada recalls

Label#2024554September 19, 2024
258,000 units affected
Issue: On certain vehicles, the compliance label may be missing information in French. The words and abbreviations listed on the label for "TIRES", "RIMS", "WITH", "FR" and "RR" and appear in English only, when they should be listed as "TIRES/PNEUS", "RIMS/JANTES", "WITH/AVEC", "FR/AVT" and "RR/ARR". Canadian regulations require this information to be listed on the label in both English and French. Safety Risk: These small errors do not affect vehicle safety. Corrective Actions: This is not a recall. Mitsubishi has corrected the compliance label for all new vehicles.
Structure#2020216May 15, 2020
81,449 units affected
Issue: On certain vehicles, road salt can corrode the front cross-member (subframe). As a result, a lower control arm could eventually detach from the cross-member. This could cause a loss of vehicle control. Safety Risk: A loss of control can create the risk of a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the front cross-member (subframe). If no significant corrosion is found, the dealer will spray a sealing and anti-corrosion coating both inside and on the cross-member. If significant corrosion is found, the dealer will replace the cross-member.
Visual System#2018083February 12, 2018
37,654 units affected
On certain vehicles, water may drain from the windshield cowl area onto the front wiper link ball joint. Over time, this could result in corrosion and/or wear to the joint, which could result in the separation of the wiper link ball. If separation were to occur, the windshield wipers could become inoperative, which could limit the driver’s visibility under certain operating conditions which may increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the wiper link rod with a countermeasure one, and will inspect the wiper motor crank arm and replace as necessary.
Brakes#2018053January 26, 2018
39,131 units affected
On certain vehicles, insufficient rust prevention to the parking brake shaft and insufficient sealing performance of the rear brake caliper boot could allow water to penetrate inside these components causing corrosion. As a result, the parking brake shaft may become stuck causing brake dragging and/or decreased parking brake performance. Additionally, the automatic adjuster for the brake pad clearance of the rear brake caliper with the built-in parking brake may not work correctly. These conditions could lead to a vehicle rollaway, which would increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect and repair the rear brakes as necessary.
Visual System#2016530October 27, 2016
27,982 units affected
On certain vehicles, water may drain from the windshield cowl area and potentially collect in the area of the wiper motor breathing hole. If the wiper motor is not operating, water could potentially enter the wiper motor through the breathing hole. If this occurs, over time, it could result in corrosion and/or an electrical conduction failure, both of which could result in the wiper motor not operating. If the wiper motor were to stop operating, the windshield wipers would become inoperative, which could limit the driver’s visibility under certain operating conditions which may increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the wiper motor with an upgraded wiper motor that will prevent water intrusion.
Seats And Restraints#2014525November 20, 2014
13,058 units affected
On certain vehicles, the lap end attachment fastener on the front passenger seat belt may not have been torqued to proper specification. If the tightening torque of the fastener is too low, road vibrations could cause the fastener to loosen further. If this were to occur, the fastener may not properly restrain the front passenger occupant in the event of a crash, which could increase the risk of injury to the seat occupant in a crash. Correction: Dealers will inspect the torque value of the front passenger seat belt lap end attachment, and correct as necessary.
Suspension#2013241July 9, 2013
62 units affected
On certain vehicles, the stabilizer link bracket on the left front strut may have been improperly welded during the manufacturing process. As a result, the bracket may detach from the strut and damage the tire and/or brake hose. Tire failure could cause the driver to lose vehicle control, whereas a damaged brake hose could cause a loss of brake fluid, which may increase stopping distances. Both issues could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the left front strut assembly.
Fuel System#2013097February 28, 2013
2,193 units affected
On certain vehicles, a wiring harness for the secondary fuel tank level sender may have been omitted during assembly. This would cause the fuel gauge to indicate a greater quantity of fuel than what remains in the tank. As a result, if the tank were to become empty, engine stalling could occur which, in conjunction with traffic, road conditions, and driver's reactions, could increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will install the correct fuel level sender harness.
Lights And Instruments#2013096February 28, 2013
1,252 units affected
Certain vehicles may not comply with the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 108 - Lighting System and Retroreflective Devices and CMVSS 114 - Theft Protection and Rollaway Protection. Due to an incorrectly adjusted brake light switch, the brake lights may remain on constantly or may illuminate intermittently, or the vehicle could be shifted out of the park position without depressing the brake pedal. These issues could result in unintended vehicle movement or increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will remove, adjust and reinstall the brake light switch

Canadian data updated August 24, 2026

U.S. NHTSA recalls

No recalls found for this make, model, and year.

Does this recall apply to my vehicle?

Matched by make, model, and model year. Many recalls affect only specific VIN ranges — confirm with your dealer using your full VIN.

What to do

Recall repairs are free at a franchised dealer in both countries. To confirm a recall applies to your specific vehicle, or to book the work, contact your manufacturer or dealer with your full VIN, or use the official channel:

NHTSA recall lookup (search by VIN) — U.S. National Highway Traffic Safety Administration
Defects and recalls database — Transport Canada

Check a 2013 Mitsubishi RVR VIN

A VIN decode confirms your vehicle's exact model year, trim and assembly plant, then runs this same recall check against it.

Data sources and coverage limits →