2012 Mitsubishi Outlander Sport recalls

• Label#2024554September 19, 2024

  258,000 units affected

  Issue: On certain vehicles, the compliance label may be missing information in French. The words and abbreviations listed on the label for "TIRES", "RIMS", "WITH", "FR" and "RR" and appear in English only, when they should be listed as "TIRES/PNEUS", "RIMS/JANTES", "WITH/AVEC", "FR/AVT" and "RR/ARR". Canadian regulations require this information to be listed on the label in both English and French. Safety Risk: These small errors do not affect vehicle safety. Corrective Actions: This is not a recall. Mitsubishi has corrected the compliance label for all new vehicles.

• Structure#2020216May 15, 2020

  81,449 units affected

  Issue: On certain vehicles, road salt can corrode the front cross-member (subframe). As a result, a lower control arm could eventually detach from the cross-member. This could cause a loss of vehicle control. Safety Risk: A loss of control can create the risk of a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the front cross-member (subframe). If no significant corrosion is found, the dealer will spray a sealing and anti-corrosion coating both inside and on the cross-member. If significant corrosion is found, the dealer will replace the cross-member.

• Electrical#2018052January 26, 2018

  45,050 units affected

  On certain vehicles, the flange of the drive belt automatic tensioner may crack over time due to repetitive high load operations and stress concentration. This could cause the drive belt to detach, leading to battery depletion, which would result in a loss of motive power and a loss of power steering assist. These issues could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the auto tensioner with a countermeasure unit.

• Visual System#2017364July 20, 2017

  42,283 units affected

  On certain vehicles, water may drain from the windshield cowl area and potentially collect in the area of the wiper motor breathing hole. If the wiper motor is not operating, water could potentially enter the wiper motor through the breathing hole. If this occurs, over time, it could result in corrosion and/or an electrical conduction failure, both of which could result in the wiper motor not operating. If the wiper motor were to stop operating, the windshield wipers would become inoperative, which could limit the driver’s visibility under certain operating conditions which may increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the wiper motor with an upgraded wiper motor that will prevent water intrusion.

• Visual System#2016529October 27, 2016

  42,283 units affected

  On certain vehicles, water may drain from the windshield cowl area onto the front wiper link ball joint. Over time, this could result in corrosion and/or wear to the joint, which could result in the separation of the wiper link ball. If separation were to occur, the windshield wipers could become inoperative, which could limit the driver’s visibility under certain operating conditions which may increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the rubber boot which covers the ball joint with a countermeasure one, and the wiper motor crank arm will also be inspected and replaced as necessary.

• Structure#2016317June 21, 2016

  64,305 units affected

  On certain vehicles, road salt can corrode the front crossmember assembly, which may ultimately lead to separation of the control arm at the mounting point. This would allow the wheel to rotate off its designed axis, and could result in a loss of vehicle control and a crash causing property damage and/or personal injury. Correction: Dealers will inspect the crossmember and apply an anti-corrosion treatment or replace the assembly, as required.

• Powertrain#2014248June 25, 2014

  3,549 units affected

  On certain 2012 to 2014 model year vehicles, due to improper manufacturing of the oil seal boss in certain transfer assemblies, the oil seal can become out of position and allow automatic transmission fluid to enter into the transfer assembly, resulting in reduced automatic transmission fluid pressure in the transaxle. This condition would illuminate the “Automatic Transmission” (A/T) warning light in the instrument panel and could result in the inability to shift gears or to drive the vehicle, increasing the risk of crash causing injury and/or property damage. Correction: Dealers will inspect and, if necessary, replace the transfer assembly. Note: Only a limited number of 2007 to 2010 model year vehicles equipped with a replacement transfer assembly are included in the recall population.

• Steering#2014247June 25, 2014

  1,635 units affected

  Certain 2013 model year vehicles with a 6-speed automatic transmission may have been manufactured with insufficient clearance between the power steering pressure tube and the bosses on the converter housing of the automatic transaxle. This may cause the power steering pressure tube to rust from abrasive contact between the two components. In the worst case, a pin hole could develop and allow for power steering fluid leakage, which can result in the loss of power steering assist and increase the risk of crash causing injury and/or property damage. Correction: Dealers will replace the power steering pressure tube and return tube. Note: Only a limited number of 2007 to 2012 model year vehicles equipped with a replacement automatic transaxle with the bosses on the converter housing are included in the recall population.

• Lights And Instruments#2012001January 4, 2012

  2,301 units affected

  Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 108 - Lighting System and Retroreflective Devices. An incorrectly manufactured turn signal lever could cause the auto-cancel function to become inoperative. The vehicle operator will, however, continue to be able to manually cancel the turn signals. Correction: Dealers will inspect and, if necessary, replace the turn signal lever.

Canadian data updated August 24, 2026

• STRUCTURE:FRAME AND MEMBERS#20V279000May 18, 2020

  Mitsubishi Motors North America, Inc. (MMNA) is recalling certain 2008-2010 Lancer, 2009-2010 Lancer Sportback, 2008-2013 Outlander, and 2011-2016 Outlander Sport vehicles originally sold in, or ever registered in, Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The front lower control arms may detach due to the front cross member corroding from salt water exposure such as from road salt use.

  Risk: A detached front control arm can result in a loss of vehicle control, increasing the risk of a crash.

  Remedy: MMNA will notify owners, and dealers will inspect the front cross members. Depending on the level of existing corrosion, either a sealing/anti-corrosion agent will be applied or the front cross member will be replaced with a new one. These repairs will be performed free of charge. The recall began August 7, 2020. Owners may contact MMNA customer service at 1-888-648-7820. MMNA's number for this recall is SR-20-003.

• VISIBILITY:WINDSHIELD WIPER/WASHER:LINKAGES#18V103000February 9, 2018

  Mitsubishi Motors North America, Inc. (MMNA) is recalling certain 2011-2016 Outlander Sport vehicles. Water may enter between the hood and windshield and cause the front wiper link ball joint to corrode, possibly resulting in the wiper link separating and the wipers becoming inoperative.

  Risk: Loss of wiper function can reduce visibility and increase the risk of a crash.

  Remedy: MMNA will notify owners, and dealers will replace the rod of the wiper link and the wiper motor crank arm, free of charge. The recall is expected to begin April 10, 2018. Owners may contact MMNA customer service at 1-888-648-7820. MMNA's number for this recall is SR-18-004.

• ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS#18V069000January 26, 2018

  Mitsubishi Motors North America, Inc. (MMNA) is recalling certain 2009-2012 Lancer, 2008-2012 Outlander, 2010-2012 Lancer Sportback, and 2011-2012 Outlander Sport vehicles equipped with either a 4B11 or 4B12 engine. The drive belt automatic tensioner flange may crack, allowing the accessory drive belt to detach.

  Risk: If the drive belt detaches, the battery will discharge and the engine will stall, increasing the risk of a crash.

  Remedy: MMNA will notify owners, and dealers will replace the belt tensioner with one that has an improved shape, free of charge. The recall is expected to begin March 27, 2018. Owners may contact MMNA customer service at 1-888-648-7820. MMNA's number for this recall is SR-18-001.

• STRUCTURE:BODY:HATCHBACK/LIFTGATE:HINGE AND ATTACHMENTS#16V867000December 2, 2016

  Mitsubishi Motors North America, Inc. (MMNA) is recalling certain model year 2011-2012 Outlander Sport vehicles manufactured August 26, 2010, to June 1, 2012, and 2016 Outlander Sport vehicles manufactured January 11, 2016, to July 8, 2016. The lift gate support outer tube on the affected vehicles may have insufficient anti-corrosion treatment that can allow the outer tube to corrode due to salt and water penetration.

  Risk: If the outer tube corrodes, there may be a rapid loss of the gas used to provide lift assistance, causing the lift gate to fall suddenly, increasing the risk of injury.

  Remedy: MMNA will notify owners, and dealers will replace the lift gate supports, free of charge. The recall began on January 20, 2017. Owners may contact MMNA customer service at 1-888-648-7820. MMNA's number for this recall is SR-16-011.

• VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR#16V792000October 31, 2016

  Mitsubishi Motors North America, Inc. (MMNA) is recalling certain model year 2011-2015 Outlander Sport vehicles manufactured August 26, 2010, to January 5, 2015. In the affected vehicles, water may drop between the hood and the windshield and leak into the wiper motor breathing hole. The water may cause internal corrosion of the windshield wiper motor and the possible failure of the motor.

  Risk: Failure of the wiper motor can cause a loss of visibility, increasing the risk of a crash.

  Remedy: MMNA will notify owners, and dealers will replace the wiper motor, free of charge. The manufacturer has begun the recall, but parts are not yet available; a second notice will be sent when parts are available. Owners may contact MMNA customer service at 1-888-648-7820. MMNA's number for this recall is SR-16-010.

• EXTERIOR LIGHTING:TURN SIGNAL#12V001000January 3, 2012

  MITSUBISHI IS RECALLING CERTAIN MODEL YEAR 2012 OUTLANDER SPORT VEHICLES, MANUFACTURED FROM NOVEMBER 9, 2011, THROUGH DECEMBER 16, 2011. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THE TURN SIGNAL LEVERS IN THE VEHICLE WERE NOT MANUFACTURED CORRECTLY, WHICH COULD RESULT IN THE AUTO-CANCEL FUNCTION OF THE TURN SIGNAL BECOMING INOPERATIVE.

  Risk: THE TURN SIGNAL MAY CONTINUE TO SIGNAL AN INTENDED DIRECTIONAL CHANGE AFTER A POINT WHEN THE AUTO-CANCEL FUNCTION, IF OPERATING PROPERLY, WOULD HAVE TERMINATED THE SIGNAL. A FOLLOWING OR ONCOMING DRIVER MAY RECEIVE INACCURATE INDICATIONS OF THE VEHICLE OPERATOR'S INTENDED MANEUVERS, THEREBY INCREASING THE RISK OF A CRASH BETWEEN VEHICLES DUE TO IMPROPER VEHICLE SIGNALING.

  Remedy: DEALERS WILL INSPECT THE TURN SIGNAL LEVER AND REPLACE IT WITH A NEW ONE FREE OF CHARGE. NO VEHICLES HAVE BEEN RETAILED TO CUSTOMERS WITH THIS POTENTIAL CONDITION, NO RECALL BULLETIN OR OWNER LETTERS WILL BE PREPARED. YOU MAY CONTACT MITSUBISHI AT 1-800-222-0037.