2014 Kenworth T660 recalls

• Lights And Instruments#2020148April 7, 2020

  65,284 units affected

  Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).

• Lights And Instruments#2015316July 20, 2015

  4,791 units affected

  Certain vehicles equipped with HID headlamps may not comply with the requirements of Canada Motor Vehicle Safety Standard 108 - Lighting System and Retroreflective Devices. A Daytime Running Lamp (DRL) that is optically combined with a turn signal lamp must switch off when the turn signal lamp is switched on as a hazard warning signal. In the affected vehicles, the DRL overrides the hazard flashing functionality after the service brake is applied for more than 2 seconds, which is contrary to the standard. The hazard functionality returns to normal when the application of the service brake is removed. Turn signal functionality would not impacted. Failure to warn oncoming vehicles with flashing hazard lamps could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will update vehicle software.

• Electrical#2015190May 8, 2015

  22,815 units affected

  On certain vehicles, water could migrate into wiper motor head and could lead to internal corrosion. This internal corrosion could form a conductive salt bridge which could result in a short circuit, causing the wiper system to fail. Loss of windshield wiping capability, should it occur during a rainy/snowy day, may compromise the driver's ability to see the road and its users, and a short circuit could increase the risk of fire, which could result in injury and/or damage to property. Correction: Dealers will install a shield over the wiper motor to protect it from water intrusions and prevent corrosion.

• Electrical#2015189May 8, 2015

  140 units affected

  On certain vehicles equipped with PACCAR MX-13 engines and Delco-Remy 40SI alternators, the alternator charge cable may chafe against an air conditioning discharge line. This chafing could lead to damage of the alternator cable's insulation and could lead to an electrical short, increasing the risk of fire, which could result in injury and/or damage to property. Correction: Dealers will rotate the alternator cable end 180 degrees to provide necessary clearance and reattach the cable to the alternator.

• Brakes#2015037January 28, 2015

  11 units affected

  On certain vehicles equipped with a Wabco quick release with double check valves, used to control park/spring brake application, the valve may leak internally. This could cause unintended partial or full park/spring brake application, which could affect service brake function and increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will affect repairs.

• Engine#2014046February 19, 2014

  82 units affected

  On certain vehicles equipped with Cummins ISL G or ISX12 G engines, incorrect engine ECU programming could cause the exhaust system temperature to become elevated during cold weather operation. This could also cause flames to be emitted from the exhaust. As a result, nearby combustible material could be ignited, increasing the risk of a fire, injury and/or damage to property. Correction: Authorized Cummins service facilities will update software programming.

• Seats And Restraints#2014020January 24, 2014

  1,646 units affected

  On certain vehicles, the seat belts may not comply with Canada Motor Vehicle Safety Standard 209 - Seat Belt Assemblies. Due to a defect in manufacturing, the seat belt buckle may not release as required by the standard. This could hinder egress from the vehicle in an emergency, increasing the risk of injury. Correction: Dealers will inspect and, if necessary, replace affected seatbelt buckles.

• Lights And Instruments#2013432December 5, 2013

  702 units affected

  The stop/turn/tail lights used on certain vehicles may not comply with the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 108 - Lighting System and Retroreflective Devices. The plastic lamp housing may shrink, causing the light to fall out of the light retention ring . In this situation, the light would no longer comply with the mounting requirements of CMVSS 108 and visibility to other motorists would be affected. This could increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will replace affected lights.

• Electrical#2013178May 24, 2013

  255 units affected

  On certain trucks, an internal defect in the ignition switch can cause the starter to engage when the key is partially inserted. This would allow the engine to start unexpectedly, which could injure someone working in the engine compartment. Also, manual transmission vehicles without the neutral start option may move unexpectedly if the transmission is in gear at the time the key is inserted. This could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the ignition switch assembly.

Canadian data updated August 24, 2026

• SERVICE BRAKES, AIR:SUPPLY:RESERVOIR/TANK#24V145000February 23, 2024

  PACCAR Incorporated (PACCAR) is recalling certain 2009-2021 Kenworth C500, 2012-2021 Kenworth T440, 2009-2015 Kenworth T660, 2015-2024 Kenworth T680, 2009-2024 Kenworth T800, 2009-2020 Kenworth T370, 2014-2023 Kenworth T880, 2011-2016 Kenworth T470, 2023 Kenworth T480, and 2009-2019 Kenworth W900 vehicles. The air tanks have an insufficient volume of air for the brake system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems."

  Risk: Insufficient air volume can reduce braking performance and increase the risk of a crash.

  Remedy: Dealers will install the correct volume air tanks, free of charge. Owner notification letters were mailed August 12, 2024. Additional owner notification letters were mailed October 27, 2025. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 24KWD.

• ELECTRONIC STABILITY CONTROL (ESC)#20V199000April 6, 2020

  PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

  Risk: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

• EXTERIOR LIGHTING:HAZARD FLASHING WARNING LIGHTS#15V458000July 22, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2011-2016 Kenworth T440, T470, T660, T680, and T880 trucks manufactured January 14, 2010, to May 22, 2015, and equipped with HID Headlamps and the option for Daytime Running Lamps (DRL). The DRLs are required to deactivate when the hazard warning lights are activated, however, the DRLs on these vehicles override the hazard flashing functionality after the brake pedal is pushed for more than two seconds. Normal hazard flashing functionality returns once the service brake is released. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, Reflective Devices, and Associated Equipment."

  Risk: If the hazard warning lamps are overridden by the DRL, oncoming vehicles may fail to be warned, increasing the risk of a crash.

  Remedy: Kenworth will notify owners, and dealers will update the cab controller software, free of charge. The recall began on September 167, 2015. Owners may contact Kenworth customer service at 1-425-828-5000. Kenworth's number for this recall is 15KWL.

• POWER TRAIN:DRIVELINE:DRIVESHAFT#15V310000May 26, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2014 and 2015 Kenworth T660, T680, and T800 trucks manufactured January 29, 2013, to April 2, 2014, and 2013 Peterbilt 587 trucks manufactured on August 8, 2012. The affected trucks are built with a driveshaft that may not transmit power to the wheels due to weld failure from corrosion.

  Risk: If the weld fails causing a loss of power to the rear wheels, the vehicle operator may be unable to move the vehicle, or may experience deceleration if the vehicle is in motion, increasing the risk of a vehicle crash.

  Remedy: PACCAR will notify owners, and dealers will replace the defective driveshafts, free of charge. The recall began on July 15, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, or Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 15KWJ and 515-H.

• ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR#15V270000May 8, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2014-2016 Kenworth T660, T680, T880 trucks manufactured February 18, 2013, to April 10, 2015, and 2011-2016 Peterbilt 386, 389, 567, 579, and 587 trucks manufactured December 13, 2010, to April 20, 2015. The affected trucks, equipped with PACCAR MX-13 engines and Delco-Remy 40SI alternators, have alternator charge cables that may chafe against a formed metal freon discharge line.

  Risk: If the alternator cable rubs through its insulation, an electrical short may occur, increasing the risk of a fire.

  Remedy: PACCAR will notify owners, and dealers will reroute the alternator charge cable away from the metal freon line, free of charge. PACCAR issued an interim notification to owners on July 10, 2015. The recall began on September 16, 2015. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. PACCAR's numbers for this recall are 15KWE and 515-F.

• VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR#15V271000May 8, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2011-2016 Kenworth T270, T370, T440, T470, C500, C540, C550, T660, T800, W900, and 963 trucks manufactured November 1, 2010, to April 6, 2015. In the affected trucks, water may leak into the wiper motor.

  Risk: As water leaks in, the wiper may cease to function on the 'intermittent' setting, reducing the driver's visibility and increasing the risk of a crash. Additionally, the water may cause corrosion which, over time, may result in an electrical short, increasing the risk of a fire.

  Remedy: PACCAR is still developing and testing a remedy. The recall is expected to begin in July 2015. An interim letter was sent to owners on July 2, 2015. The recall began on September 2, 1015. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 15KWF.

• ENGINE AND ENGINE COOLING:ENGINE#14V086000February 18, 2014

  PACCAR Inc, is recalling certain model year 2014-2015 Kenworth T440, T660, T800, and W900 tractor trailers manufactured January 23, 2013, through February 4, 2014, and certain model year 2014-2015 Peterbilt 320, 365, 382, 384 tractor trailers manufactured January 21, 2013, through February 5, 2014, and equipped with certain Cummins Westport Model ISL G and ISX12 G engines. Condensation in the intake manifold may freeze during cold weather conditions and interfere with the proper operation of the intake manifold pressure sensor.

  Risk: The improper operation of the sensor could induce elevated exhaust temperatures or flames from the exhaust pipe, increasing the risk of a vehicle fire or burn injury to a person near the exhaust pipe.

  Remedy: PACCAR will notify owners, and authorized Cummins service facilities will upload a new ECM calibration, free of charge. The recall began on April 12, 2014. Customers may contact PACCAR at 1-425-468-7400. Paccar's recall numbers associated with this campaign are 14KWG (Kenworth), and 214-C (Peterbilt).

• PARKING BRAKE#14V027000January 29, 2014

  PACCAR Incorporated (PACCAR)is recalling certain model year 2013-2014 T660, and T680 vehicles manufactured from December 4, 2012, through September 17, 2013 and configured as a dead axle tandem with air disc brakes and spring brake delete options. The affected vehicles have the parking brake incorrectly placed on the non-driven rear axle.

  Risk: If the parking brake is on the non-driven axle the vehicle could roll away when the parking brakes are set, resulting in an increased risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will move the parking brake components to the forward wheel axle, free of charge. The recall began on April 9, 2014. Owners may contact PACCAR at 1-425-468-7400. Paccar's number for this recall is 14KWE.

• SEAT BELTS#14V013000January 24, 2014

  PACCAR Incorporated (PACCAR) is recalling certain model year 2014 Kenworth T660, T680, T700,T800, T880, W900, T440, T470, T370, T270, T170, C500, and C550 chassis manufactured between August 7, 2013, and October 31, 2013, and Peterbilt 320, 325, 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, and 587 chassis manufactured between August 7, 2013, and November 3, 2013, and equipped with IMMI-brand L9 seat belt buckles. When the button is pressed to release the seat belt, the latch plate can become partially engaged with the buckle, making the seat belt difficult to unlatch. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 209, "Seat Belt Assemblies."

  Risk: If the latch plate remains partially engaged after the button is pressed, egress from the vehicle could be hindered which would increase the risk of injury in the event of an emergency.

  Remedy: PACCAR will notify owners, and dealers will inspect and replace the seat belt buckles, as necessary, free of charge. The recall began on March 31, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's number for this campaign is 14KWC. Peterbilt's number for this campaign is 114-B.

• EXTERIOR LIGHTING:TAIL LIGHTS#13V612000December 5, 2013

  PACCAR Incorporated (Paccar) is recalling certain model year 2014 Kenworth T170, T270, T370, T440, T470, T660, T680, T700, T800, T880, C500 and W900 trucks manufactured July 1, 2013 through September 17, 2013. In the affected vehicles, the plastic housing of the Stop/Tail/Turn (STT) lamp can shrink and allow the light bulb to fall out of the mounted retention ring. As such, the Stop/Tail/Turn light would not be illuminated, and the vehicles do not conform to Federal Motor Vehicle Safety Standard (FMVSS) No. 108 "Lamps, Reflective Devices, and Associated Equipment."

  Risk: If the stop/tail/turn light is not illuminated, the driver's intentions would not be communicated, which increases the risk of a crash.

  Remedy: Kenworth will notify owners, and dealers will replace the defective STT lamps with new lamps. The recall began on February 4, 2014. Customers may contact Paccar at 1-425-468-7400. Kenworth's number for this recall is 13KWM.

• ELECTRICAL SYSTEM:IGNITION:SWITCH#13V222000May 28, 2013

  PACCAR is recalling certain model year 2014 Kenworth T170, T270, T370, T470, T660, T680, T800, T880, and W900 trucks manufactured May 6, 2013, through May 17, 2013; and model year 2014 Peterbilt 330, 337, 348, 365, 367, 382, 384, 386, 388, 389, 389K, 567, 579 and 587 trucks manufactured May 1, 2013 through May 17, 2013. An internal defect in the ignition switch causes the starter to engage when a key is partially inserted, before the key is turned.

  Risk: Unintended engine startup could cause injury to a person working in the engine compartment. Vehicles with standard transmissions may experience unexpected movement, which may result in personal injury or a crash.

  Remedy: PACCAR will notify owners, and dealers will replace affected ignition switches, free of charge. The recall began on June 14, 2013. Owners may contact Kenworth at 1-425-828-5000 or Peterbilt at 1-940-591-4000. Kenworth's recall campaign number is 13KWF. Peterbilt's recall campaign number is 0513-E.