Toyota Matrix recalls

• Electrical#2021723November 24, 2021

  55,683 units affected

  Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.

• Airbag#2020013January 17, 2020

  407,318 units affected

  Issue: On certain vehicles, the circuits within the airbag control module could be damaged in a crash. This could cause the airbags and seat belt pretensioners to not deploy in certain crashes. Safety Risk: Airbags or seat belts that do not work properly in a crash could create an increased risk of injury. Corrective Actions: Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to install an electrical noise filter to prevent damage to the airbag control module.

• Airbag#2019008January 9, 2019

  376,282 units affected

  Issue: On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, may eventually degrade the propellant contained in the passenger-front airbag. This could cause the airbag to deploy with more force than normal. If the airbag inflator ruptures, fragments could be propelled toward vehicle occupants or cause damage to the airbag assembly, preventing its proper function. Safety Risk: If the vehicle is involved in a crash requiring an airbag deployment, the airbag inflator could rupture and create a risk of injury. Corrective Action: Owners will be notified by mail and instructed to take their vehicle to a dealer to have the passenger-front airbag inflator or airbag module replaced. Note: The Canadian climate results in the propellant degrading slowly. This recall is being conducted as a precaution to address future risk. It is expected that all airbag inflators will be replaced before their function would be affected.

• Electrical#2015493October 21, 2015

  315,091 units affected

  On certain vehicles, inconsistent application of grease during the manufacturing process could cause the driver's side power window master switch to stick or become inoperative due to electrical contact point wear. This could cause debris to accumulate between the contact points, potentially resulting in an electrical short circuit. If a short circuit occurs, the switch assembly may overheat, produce smoke, melt and/or potentially lead to a fire causing injury and/or property damage. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary. Note: This is an expansion of recall 2012-338.

• Airbag#2014124April 9, 2014

  344,870 units affected

  On certain vehicles, electrical circuitry in the steering wheel assembly may become damaged. As a result, the driver's airbag may not function as intended, causing the instrument panel airbag warning lamp to illuminate. Failure of the driver's airbag to deploy during a crash (where deployment is warranted) could increase the risk of injury to the seat occupant. Correction: Dealers will replace the spiral cable assembly.

• Label#2013462December 20, 2013

  146 units affected

  Certain vehicles may not comply with the requirements of Canada Motor Vehicle Safety Standard 110 - Tire Selection and Rims. The Tire and Loading Information label may contain incorrect front tire size information. Correction: Dealers will inspect the Tire and Loading Information Label and install a revised label if necessary.

• Other#2010012January 22, 2010

  273,050 units affected

  On certain vehicles, accelerator pedal movement may become rough, slow to return, or the pedal may stick in a depressed position. This could result in a loss of throttle control and a vehicle crash, causing property damage, personal injury or death. Correction: Dealers will install a steel reinforcement bar to the accelerator pedal assembly. With this reinforcement in place, the excess friction that can cause the pedal to stick is eliminated.

• Other#2009290October 7, 2009

  437,445 units affected

  On certain vehicles, the accelerator pedal may become stuck in the wide open position due to an unsecured or incompatible driver's floor mat. A stuck open accelerator pedal may result in very high vehicle speeds and make it difficult to stop the vehicle, which could cause a crash, serious injury or death. Correction: Dealers will reconfigure the shape of the accelerator pedal. Certain models will also have the shape of the floor underneath the accelerator pedal modified and/or a brake override system installed.

• Brakes#2009251August 26, 2009

  103,932 units affected

  On certain vehicles, when driven in extremely low ambient temperatures, the intake manifold suction port for the brake vacuum can become blocked due to the freezing of condensation emanating from Positive Crankcase Ventilation (PCV). Should the suction port become blocked, vacuum assist to the brakes would be insufficient and the increased pedal pressure required could lead to an increase in vehicle stopping distance. Extended stopping distances may result in a vehicle crash causing property damage, personal injury or death. Correction: Dealers will install a newly designed intake air connector which will relocate the brake system vacuum port.

Canadian data updated August 24, 2026