Does the 2012 Shred-Tech MDS-26GTX have any recalls?

Transport Canada lists 1 campaign and the U.S. NHTSA lists 1 for the 2012 Shred-Tech MDS-26GTX. Matched by make, model, and model year. Many recalls affect only specific VIN ranges — confirm with your dealer using your full VIN.

How do I know if a recall applies to my 2012 Shred-Tech MDS-26GTX?

Recalls are matched by make, model and model year, but many cover only certain VIN ranges. Confirm with your manufacturer or dealer using your full VIN, or use the official Transport Canada or NHTSA lookup.

Are recall repairs free?

Yes. In both Canada and the United States the manufacturer must fix a recalled defect at no charge, through a franchised dealer.

RECALLS — MAKE · MODEL · YEAR

2012 Shred-Tech MDS-26GTX recalls

2 safety recall campaigns have been filed for the 2012 Shred-Tech MDS-26GTX with Transport Canada and the U.S. NHTSA. Here is what both agencies say.

Canadian recalls: 01
U.S. recalls: 01
Total campaigns: 02

Transport Canada recalls

Accessories#2015276June 19, 2015
8 units affected
On certain mobile document shredder vehicles, installation of the shredding equipment combined with the increased weight of additional emissions components may have caused the vehicle weight to exceed the front gross axle weight rating (GAWR). This would result in vehicle being overloaded, potentially affecting vehicle handling characteristics, which could result in a crash causing injury and/or property damage. Correction: For vehicles built on the Freightliner M2 106 chassis, dealers will provide a new compliance label to reflect an increased GAWR (to 9000 lbs from 8000 lbs), and upgrade the front axle as necessary. For vehicles built on the Hino 258LP chassis, dealers will provide a new compliance label to reflect an increased GAWR (to 8500 lbs from 8000 lbs).

Canadian data updated August 24, 2026

U.S. NHTSA recalls

EQUIPMENT:OTHER:LABELS#15V405000June 24, 2015
Shred-Tech Corporation (Shred-Tech) is recalling certain model year 2011-2013 MDS-20GT vehicles manufactured July 1, 2011, to March 1, 2013, 2010-2013 MDS-26GTX vehicles manufactured August 2, 2010, to March 1, 2013, 2013-2015 MDS 1/26 vehicles manufactured April 1, 2013, to May 1, 2015, and 2013-2015 MDS 2/26 vehicles manufactured March 1, 2015, to May 29, 2015. The affected vehicles were built on Hino 258LP and Freightliner M2 106 chassis and are equipped with EPA 2010 Emission Controls. With the EPA controls, the vehicles exceed the front axle Gross Axle Weight Rating (GAWR) specified on the certification label. As such, these vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification."
Risk: If the axle weight on the certification label is exceeded, it can cause poor vehicle handling or front axle failure, increasing the risk of a vehicle crash.
Remedy: Shred-Tech will notify owners, and dealers will install a revised certification label on vehicles built on Freightliner M2 chassis increasing the GAWR to 9,000 pounds, and will modify the wheel base to redistribute the weight on vehicles built on Hino 258LP chassis, free of charge. The recall began on July 30, 2015. Owners may contact Shred-Tech customer service at 1-800-465-3214.

Does this recall apply to my vehicle?

Matched by make, model, and model year. Many recalls affect only specific VIN ranges — confirm with your dealer using your full VIN.

What to do

Recall repairs are free at a franchised dealer in both countries. To confirm a recall applies to your specific vehicle, or to book the work, contact your manufacturer or dealer with your full VIN, or use the official channel:

NHTSA recall lookup (search by VIN) — U.S. National Highway Traffic Safety Administration
Defects and recalls database — Transport Canada

Check a 2012 Shred-Tech MDS-26GTX VIN

A VIN decode confirms your vehicle's exact model year, trim and assembly plant, then runs this same recall check against it.

Data sources and coverage limits →