2017 Peterbilt 579 recalls

• Lights And Instruments#2020148April 7, 2020

  65,284 units affected

  Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).

• Electrical#2020090March 5, 2020

  2,435 units affected

  Issue: On certain trucks, the battery cables to the jump-start terminal may be too long. As a result, the cables could contact and chafe against the left-front suspension leaf spring. If this happens, a short circuit could occur and cause the positive cable to overheat or melt. Note: This recall only affects trucks with a left-hand under-hood battery jumper terminal. Safety Risk: An overheated or melted battery cable could create the risk of a fire. Corrective Actions: The company will notify owners by mail and instruct you to take your truck to a dealer for an inspection of the jump-start terminal cables. If the cables are too long, they will be replaced.

• Fuel System#2018527September 25, 2018

  2,974 units affected

  On certain trucks built with a Cummins X15 or ISX15 engine equipped with nylon fuel lines and a banjo bolt on the fuel pump, a blockage in the fuel cooling system may cause a fuel line to burst. This could result in a significant fuel leak onto the roadway, which would create a road hazard for other motorists. Additionally, this condition could also cause an engine stall without warning, without the ability to restart the engine. Both of these conditions may increase the risk of a crash causing injury and/or damage to property. Correction: Cummins-authorized dealers will replace the affected nylon line with a steel line.

• Brakes#2018389July 24, 2018

  214 units affected

  Certain vehicles may fail to conform to the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 121 - Air Brake Systems and CMVSS 136 - Electronic Stability Control Systems for Heavy Vehicles. In the event that the anti-lock brake system (ABS) loses battery and/or ignition power to the controller, the ABS indicator lamp may not illuminate to warn the driver of the loss of ABS, which is contrary to the requirements of the standards. This could result in the loss of ABS function with no warning to the driver, which could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will reprogram the cab control module.

• Lights And Instruments#2018077February 8, 2018

  174 units affected

  Certain vehicles equipped with Eaton Ultrashift Plus or Eaton Advantage automatic transmissions with right hand stalk shifters may not comply with the requirements of Canada Motor Vehicle Safety Standards (CMVSS) 101 - Location and Identification of Controls and Displays and CMVSS 102 – Transmission Control Functions. Under certain conditions, the D-R-N (Drive-Reverse-Neutral) display in the instrument cluster may incorrectly illuminate the "N" on the display when the transmission shifter is in the "D" or "R" position, which is contrary to the requirements of the standards. This could create confusion to the operator, which could increase the risk of injury and/or property damage. Correction: Dealers will update the transmission software.

• Electrical#2017374July 27, 2017

  240 units affected

  On certain vehicles, the polyfuse for the spotlight could develop a short circuit in the cabin fuse box. A short circuit could result in overheating and melting of the fuse box, and could increase the risk of a fire causing injury and/or damage to property. Correction: Dealers will replace the optional polyfuse switch in the spotlight circuit with a standard fuse.

• Fuel System#2017361July 20, 2017

  533 units affected

  On certain vehicles equipped with Cummins ISX 15 engines and certain fuel pumps, the drive gear on the fuel pump may spin loose on the drive shaft. This could result in a loss of pumping function, which could result in an engine stall without warning and not being able to be restarted, which could increase the risk of a crash causing injury and/or damage to property. Correction: Cummins-authorized dealers will replace the fuel pump.

• Fuel System#2017093February 20, 2017

  23 units affected

  On certain vehicles equipped with 2017 emissions engines, a tee fitting in the fuel supply was improperly manufactured and could leak fuel. Leaking fuel, in the presence of an ignition source, could result in a fire causing injury and/or damage to property. Correction: Dealers will inspect and replace affected fittings as necessary.

• Engine#2016289June 8, 2016

  178 units affected

  On certain vehicles, the Engine Control Module (ECM) may develop an internal electrical short circuit that could blow a fuse in the ECM's electrical supply circuit. This could cause the engine to stall without warning and prevent the vehicle from being restarted. Engine stalling without warning would result in lost propulsion which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will replace the ECM.

Canadian data updated August 24, 2026

• ELECTRICAL SYSTEM:WIRING#21V00N000December 29, 2021

  PACCAR Incorporated (PACCAR) is recalling certain 2016-2022 Peterbilt 567, 579, 2021-2022 Peterbilt 536, 2017-2021 Kenworth T880, 2016-2022 Kenworth T680, 2018-2020 Kenworth T440, 2020 Kenworth T270, and 2021 Kenworth T280 vehicles. The methane detection system will not function if the system loses power.

  Risk: The operator may be unaware of a system malfunction or the presence of excessive methane levels, increasing the risk of injury or fire.

  Remedy: Dealers will re-wire the warning alarm, free of charge. Owner notification letters were mailed December 1, 2022. Owners may contact Peterbilt customer service at 1-940-591-4220, and Kenworth customer service at 1-425-828-5888. PACCAR's numbers for this recall are 21KWH and 21PBN.

• ELECTRONIC STABILITY CONTROL (ESC)#20V199000April 6, 2020

  PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

  Risk: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

• ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES#20V130000March 4, 2020

  PACCAR Incorporated (PACCAR) is recalling certain 2015-2020 Peterbilt 365, 389, 567, and 579 vehicles equipped with a left-hand under hood jumper terminal (option code 2539410). The positive battery jumper terminal cable may be too long, allowing it to chafe against the left front suspension spring and result in an electrical short circuit.

  Risk: An electrical short circuit can increase the risk of a fire.

  Remedy: PACCAR will notify owners, and dealers will inspect the battery jumper terminal cables, and replace them as necessary, free of charge. The recall began April 30, 2020. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 20PBA.

• ELECTRONIC STABILITY CONTROL (ESC)#19V657000September 17, 2019

  Transportation Power, Inc. (TransPower) is recalling certain 2017-2018 electric trucks built on Peterbilt 579 chassis. The vehicles do not have stabilization hardware and software that interacts with the braking system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 136, "Electronic Stability Control Systems on Heavy Vehicles."

  Risk: Without a Electronic Stability Control system, there is a greater chance of loss of stability control, which increases the risk of a crash.

  Remedy: TransPower will notify owners, and dealers will install an Electronic Stability Control (ESC) system, free of charge. The recall began September 26, 2019. Owners may contact TransPower customer service at 1-858-248-4255.

• EXTERIOR LIGHTING#18V816000November 16, 2018

  PACCAR Incorporated (PACCAR) is recalling certain 2013-2019 Kenworth T680 and T880 and Peterbilt 579 trucks, greater than 30 feet long and equipped with side extender mounted intermediate marker lamp/turn signals that do not include a reflex reflector. Since both intermediate side marker lamps and reflex reflectors are required, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

  Risk: Missing reflex reflectors can reduce the vehicle's visibility to other drivers, increasing the risk of a crash.

  Remedy: PACCAR will notify owners and dealers will install reflex reflective tape, free of charge. The recall began January 15, 2019. Owners may contact PACCAR customer service at 1-918-259-3258. PACCAR's number for this recall is 18KWF, and 18PBC.

• ENGINE AND ENGINE COOLING:ENGINE:DIESEL#18V657000September 21, 2018

  PACCAR Incorporated (PACCAR) is recalling certain 2017-2019 Kenworth C500, T600, T660, T680, T800, T880 and W900 trucks, as well as Peterbilt 367, 386, 389, 567, 579 and 587 trucks, equipped with Cummins ISX15 or X15 diesel engines. In certain driving conditions, such as on a long down-hill grade, the fuel line may burst if the fuel pump cooling circuit screen becomes restricted.

  Risk: If the fuel line bursts, fuel may leak onto the road resulting in a roadway hazard for other motorists. The engine may also stall without warning, resulting in the vehicle's inability to restart, increasing the risk of a crash.

  Remedy: Cummins will notify owners, and dealers will replace the suspect fuel pump cooling circuit screen, free of charge. The recall began November 21, 2018. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 18E081.

• ELECTRONIC STABILITY CONTROL (ESC)#18V368000June 1, 2018

  PACCAR Incorporated (PACCAR) is recalling certain 2017-2018 Peterbilt 567 and 579 trucks and 2015-2018 Kenworth T660, T680, T800, T880 and W900 trucks. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

  Risk: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on July 30, 2018. Owners may contact Peterbilt customer service at 1-918-259-3258 or Kenworth customer service at 1-425-828-5000.

• ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL#18V092000February 2, 2018

  PACCAR Incorporated (PACCAR) is recalling certain 2017-2018 Kenworth T680 and T880 trucks, and Peterbilt 567 and 579 trucks, all equipped with an automated Eaton UltraShift Plus or Eaton Advantage Transmission with right hand stalk shifter. The display that indicates which transmission gear the driver selected may display incorrectly. The display can indicate 'N' when the shifter is set into 'D' or 'R', and the as a result, the truck will not move. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 102, "Transmission Shift Lever Sequence/Starter Interlock/Transmission Braking Effect," and number 101, "Control and Displays."

  Risk: A truck that does not move as expected can increase the risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will install a transmission software update, free of charge. The recall began on March 9, 2018. Owners may contact Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4220. PACCAR's numbers for this recall is 18KWA and 118-A.

• EXTERIOR LIGHTING#17V471000July 25, 2017

  PACCAR Incorporated (PACCAR) is recalling certain 2013-2017 Peterbilt 567 and 579 Kenworth T680 and T880 trucks equipped with optional spotlights. The spotlight circuit may not be adequately protected in the event of a short.

  Risk: A short in the spotlight circuitry may increase the risk of a fire at the cab fuse block.

  Remedy: PACCAR will notify owners, and dealers will change the polyfuse switch in the spotlight circuit to a standard fuse, free of charge. The recall began on September 19, 2017. Owners may contact PACCAR customer service at 1-940-591-4220. PACCAR's number for this recall is 17KWC and 717-B.

• FUEL SYSTEM, DIESEL#17V443000July 13, 2017

  PACCAR Incorporated (PACCAR) is recalling certain 2017-2018 Peterbilt 367, 389, 567, 579 and 587 trucks, and 2018 Kenworth C500, T680, T800, T880 and W900 trucks equipped with Cummins ISX 15L engines. These engines have a fuel pump whose drive gear could possibly slip on its drive shaft, causing a fuel pump function loss, resulting in an engine stall.

  Risk: An engine stall can increase the risk of a crash.

  Remedy: Cummins will notify the vehicle purchaser, and Cummins dealers will replace the fuel pumps, free of charge. The recall began July 1, 2017. Owners may contact Cummins customer service at 1-800-286-6467 or PACCAR customer service at 1-425-468-7400. PACCAR's number for this recall is C1909.

• FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS#17V103000February 15, 2017

  PACCAR Incorporated (PACCAR) is recalling certain 2015-2018 Kenworth K370, T680, T880 and 2017-2018 Peterbilt 567 and 579 trucks. The plastic fuel tee fittings on these trucks may leak fuel.

  Risk: A fuel leak in the presence of an ignition source can increase the risk of a fire.

  Remedy: Kenworth and Peterbilt will notify owners, and dealers will replace the suspect fuel tees, free of charge. The recall began on April 13, 2017. Owners may contact Kenworth customer service at 1-425-828-5000 and Peterbilt customer service at 1-940-591-4000. PACCAR's numbers for this recall is 17KWA and 217-A.

• TIRES#16V803000November 4, 2016

  PACCAR Incorporated (PACCAR) is recalling certain model year 2017 Kenworth K370, T270, T370, T440, T660, T800 trucks manufactured February 2, 2016, to October 13, 2016, and Peterbilt 330, 337, 348, 367, 389, 567, and 579 trucks manufactured March 7, 2016, to October 5, 2016. The affected vehicles are equipped with certain Goodyear LHS Load Range G tires, size 295/75R22.5 G399A, that due to incomplete adhesion, have a tire tread that may partially separate.

  Risk: A partial tread separation may increase the risk of a crash.

  Remedy: Goodyear will notify the owners of the affected Peterbilt and Kenworth vehicles and Goodyear dealers will replace the affected tires, free of charge. The recall began on December 14, 2016. To find a Goodyear dealer, owners should contact Goodyear Consumer Relations at 1-800-592-3267. Consumers may also contact Kenworth customer service at 1-425-828-5000 and Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 1016G (PB) (Peterbilt), and 16KWC (Kenworth).

• ELECTRICAL SYSTEM:IGNITION:MODULE#16V426000June 10, 2016

  PACCAR Incorporated (PACCAR) is recalling certain model year 2017 Kenworth C500, T660, T680, T800, T880, and W900 vehicles manufactured March 9, 2016, to April 26, 2016 and 2017 Peterbilt 320, 365, 367, 389, 567, 579, and 587 vehicles manufactured March 10, 2016, to May 6, 2016. The affected vehicles are equipped with Cummins ISX12 or ISX15 engines and have an engine control module (ECM) that may short circuit, causing the engine to stall without warning without the ability to restart it.

  Risk: An engine stall can increase the risk of a crash.

  Remedy: Cummins will notify owners, and Cummins dealers will replace the defective engine control modules, free of charge. The began on July 8, 2016. Owners may contact Cummins customer service at 1-800-343-7357, Kenworth customer service at 1-425-828-5000 or Peterbilt customer service at 1-940-591-4000. PACCAR's numbers for this recall are 16KWB (Kenworth) and 616-C (Peterbilt).