Peterbilt 365 recalls

• Powertrain#2024161March 8, 2024

  5,051 units affected

  Issue: On certain trucks, the wiring in the right-hand shift stalk may not be properly connected. As a result, you may not be able to shift the transmission back into gear after coming to a stop. Safety Risk: A loss of power to the wheels could increase the risk of a crash. Corrective Actions: PACCAR will notify owners by mail and advise you to take your truck to a dealership to inspect and, if necessary, replace the right-hand shift stalk assembly.

• Lights And Instruments#2022591October 17, 2022

  7,491 units affected

  Issue: On certain trucks, a software problem could cause the instrument cluster display to freeze while driving. As a result, you may not be able to see certain information about the vehicle, including the speedometer, warnings, and malfunction tell-tale graphics. Safety Risk: Warnings and malfunction tell-tale information that does not display could increase the risk of a crash. Corrective Actions: Paccar will notify owners by mail and instruct you to take your vehicle to a dealership to update the system software.

• Steering#2022210April 25, 2022

  985 units affected

  Issue: On certain trucks, the fasteners that attach the steer arm to the steering knuckle may fail. If this happens, the steer arm could separate from the steering knuckle and cause a loss of steering control. Note: This recall only affects trucks equipped with a Dana D-series steer axle. Safety Risk: A loss of steering control could increase the risk of a crash. Corrective Actions: PACCAR will notify owners by mail. The corrective actions for this recall are under development.

• Fuel System#2021323May 26, 2021

  19 units affected

  Issue: On certain trucks, the fuel rail assembly could develop a leak. Note: This recall only affects trucks equipped with a Cummins L9 or ISX12 diesel engine. Safety Risk: A fuel leak can create the risk of a fire. Corrective Actions: Cummins will notify owners by mail and instruct you to take your truck to a Cummins authorized service center to inspect the fuel rail. If damage is found, the fuel rail and fuel lines will be replaced. If no damage is found, the fuel rail will be reassembled with new crush washers using a special tool.

• Suspension#2020399August 27, 2020

  502 units affected

  Issue: On certain trucks, the lift axle pivot bolts may be too short and may not be properly tightened. As a result, the bolts could come loose or break. If this happens, parts could fall from the truck. Note: This recall only affects trucks built with Watson Chalin SL2065 lift axles. Safety Risk: Large fasteners that fall on the road could create a road hazard for others and increase the risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to inspect and replace the lift axle pivot bolts, as necessary.

• Lights And Instruments#2020148April 7, 2020

  65,284 units affected

  Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).

• Electrical#2020090March 5, 2020

  2,435 units affected

  Issue: On certain trucks, the battery cables to the jump-start terminal may be too long. As a result, the cables could contact and chafe against the left-front suspension leaf spring. If this happens, a short circuit could occur and cause the positive cable to overheat or melt. Note: This recall only affects trucks with a left-hand under-hood battery jumper terminal. Safety Risk: An overheated or melted battery cable could create the risk of a fire. Corrective Actions: The company will notify owners by mail and instruct you to take your truck to a dealer for an inspection of the jump-start terminal cables. If the cables are too long, they will be replaced.

• Powertrain#2018739December 24, 2018

  2,634 units affected

  On certain vehicles equipped with an Eaton automated manual transmission and electronic clutch actuator (ECA), the clutch may have been manufactured improperly and could fail. If this occurs, the broken clutch components could prevent the transmission from disengaging or shifting to neutral. This could result in unintended vehicle movement, even if the parking brake is applied, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will recalibrate the Transmission Control Module (TCM).

• Brakes#2018389July 24, 2018

  214 units affected

  Certain vehicles may fail to conform to the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 121 - Air Brake Systems and CMVSS 136 - Electronic Stability Control Systems for Heavy Vehicles. In the event that the anti-lock brake system (ABS) loses battery and/or ignition power to the controller, the ABS indicator lamp may not illuminate to warn the driver of the loss of ABS, which is contrary to the requirements of the standards. This could result in the loss of ABS function with no warning to the driver, which could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will reprogram the cab control module.

• Steering#2017461September 25, 2017

  281 units affected

  On certain vehicles, the castellated nut and cotter pin on the steer axle may not have been tightened to specification. This could cause the tie rod to become loose in the steer axle, which would result in audible noise and/or looseness in steering. If the vehicle were continued to be operated in this condition, the tie rod could disconnect from the knuckle, resulting in a complete loss of control of a vehicle wheel, which would increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the torque of the castellated nuts on the tie rod, and replace the tie rod stud and knuckle as necessary.

• Brakes#2016603December 2, 2016

  184 units affected

  On certain vehicles, the stop lamps may fail to activate due to a defective weld and incomplete circuit within the stop lamp switch. If the stop lamp switch fails during the application of the service brakes, the brake lights on the vehicle and trailer will not illuminate, thereby increasing the possibility of a crash causing injury and/or damage to property. Correction: Dealers will inspect and replace any 08-01760 stop lamp switches with a suspect date code (1056, 1026, 0821, 1386 and 1456).

• Engine#2016289June 8, 2016

  178 units affected

  On certain vehicles, the Engine Control Module (ECM) may develop an internal electrical short circuit that could blow a fuse in the ECM's electrical supply circuit. This could cause the engine to stall without warning and prevent the vehicle from being restarted. Engine stalling without warning would result in lost propulsion which, in conjunction with traffic and road conditions, and the driver's reactions, could increase the risk of a crash causing property damage and/or personal injury. Correction: Dealers will replace the ECM.

• Tires#2015531November 9, 2015

  520 units affected

  On certain vehicles equipped with Michelin MN 295/60R22.5 XZA-2 front tires, the programmed maximum vehicle speed may exceed the speed rating of the tire. This could result in premature tire failure to occur under certain operating conditions (higher speeds, load and road temperature). A tire failure could cause the driver to lose vehicle control, which may result in a crash causing injury and/or property damage. Correction: Dealers will reprogram the engine’s vehicle speed parameters to limit the maximum vehicle speed to the tire speed rating.

• Engine#2015418September 23, 2015

  9 units affected

  On certain vehicles equipped with a Cummins engine, the Engine Control Module (ECM) could develop an internal electrical short circuit that could blow a fuse in the ECM’s electrical supply circuit. This could result in an unexpected engine stall without the ability to restart the engine, which could increase the risk of a crash. Correction: Dealers will replacing the existing, affected ECM with a new ECM.

• Electrical#2015317July 20, 2015

  86 units affected

  On certain vehicles equipped with PACCAR MX-13 engines and Leece Neville alternators, the alternator charge cable may chafe against an air conditioning discharge line. This chafing could lead to damage of the alternator cable's insulation and could lead to an electrical short, increasing the risk of fire, which could result in injury and/or damage to property. Correction: Dealers will rotate the alternator cable end 180 degrees to provide necessary clearance and reattach the cable to the alternator.

• Engine#2015211May 15, 2015

  169 units affected

  On certain vehicles equipped with Cummins Westport ISL-G engines, excessive engine crankcase pressure could cause the vent tube assembly elbow to detach from the breather. This could allow engine oil to come in contact with hot surfaces, increasing the risk of fire resulting in injury and/or damage to property. Correction: Dealers will install clamps at both ends of the elbow of the breather tube assembly and reprogram the Electronic Control Module (ECM) to improve diagnostic capabilities.

• Label#2015095March 5, 2015

  30,064 units affected

  Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 120 - Tire Selection and Rims. The tire information label may indicate incorrect tire pressure, understated by 5 PSI, or a tire/rim/inflation pressure combination for which the maximum GAWR is slightly below the GAWR of the vehicle. Underinflated tires may not be capable of supporting the maximum load as reflected by the GAWR and GVWR specified on the certification label, which could cause tire failure resulting in injury and/or damage to property. Correction: Manufacturer will mail new tire and rims certification label.

• Steering#2015078February 20, 2015

  574 units affected

  On certain vehicles, the tie rod end clamp bolts may not have been tightened to the correct specification. As a result, the tie rod ends could loosen, corrode, and eventually separate from the tie rod, resulting in a loss of steering control, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace tie rod assembly where the factory installed assembly has not been replaced.

• Fuel System#2014339August 7, 2014

  199 units affected

  On certain vehicles equipped with Cummins ISB and ISL engines, the fuel filter shell and nut plate could separate, causing a fuel leak and also causing the engine to stall. Stalling would result in a loss of motive power, increasing the risk of a crash resulting in injury and/or damage to property. Correction: Dealers will replace the fuel filter.

• Airbag#2014198May 29, 2014

  4 units affected

  On certain vehicles, a wiring defect could cause the airbag warning lamp to fail to illuminate in the event of a fault with the side curtain airbag system. As a result, a fault could go undetected by the driver, and cause the side airbag to fail to deploy in a crash. This could increase the risk of injury. Correction: Dealers will affect repairs.

• Brakes#2014094March 25, 2014

  27 units affected

  Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 121 - Air Brake Systems. Incorrect brake linings were used on front drum brake assemblies fitted with large diameter tires (Static Load Radius of 20.5" - 21.5"), rendering the vehicles noncompliant to the standard. This could result in inadequate braking, increasing stopping distances and increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will install new brake shoes with the correct linings.

• Engine#2014046February 19, 2014

  82 units affected

  On certain vehicles equipped with Cummins ISL G or ISX12 G engines, incorrect engine ECU programming could cause the exhaust system temperature to become elevated during cold weather operation. This could also cause flames to be emitted from the exhaust. As a result, nearby combustible material could be ignited, increasing the risk of a fire, injury and/or damage to property. Correction: Authorized Cummins service facilities will update software programming.

• Seats And Restraints#2014020January 24, 2014

  1,646 units affected

  On certain vehicles, the seat belts may not comply with Canada Motor Vehicle Safety Standard 209 - Seat Belt Assemblies. Due to a defect in manufacturing, the seat belt buckle may not release as required by the standard. This could hinder egress from the vehicle in an emergency, increasing the risk of injury. Correction: Dealers will inspect and, if necessary, replace affected seatbelt buckles.

• Electrical#2013178May 24, 2013

  255 units affected

  On certain trucks, an internal defect in the ignition switch can cause the starter to engage when the key is partially inserted. This would allow the engine to start unexpectedly, which could injure someone working in the engine compartment. Also, manual transmission vehicles without the neutral start option may move unexpectedly if the transmission is in gear at the time the key is inserted. This could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the ignition switch assembly.

• Brakes#2012027January 27, 2012

  1,434 units affected

  On certain trucks equipped with Bendix ATR-6 Antilock Traction Relay valves, in extremely cold conditions (at or below -18 degrees Celsius), internal ATR valve leakage can occur. This could cause unintended brake application, which could overheat the affected brakes and cause a fire. Also, in certain low traction conditions, unexpected brake application can cause a loss of vehicle control and a crash. These issues could result in property damage and/or personal injury. Correction: Dealers will update the cover assembly on the ATR valves.

• Powertrain#2011263July 21, 2011

  23 units affected

  On certain trucks equipped with a PACCAR MX engine and Eaton Ultrashift DM or Allison automatic transmission (without auto-neutral), the Fast Idle Control (also known as high idle) may be activated by the operator while the transmission is in gear. This could override the parking brake, allowing the vehicle to move unexpectedly. Unintended vehicle movement could result in a crash causing property damage and/or personal injury. Correction: Dealers will update the engine control software.

• Engine#2011087February 25, 2011

  589 units affected

  On certain vehicles equipped with a PACCAR MX engine, the oil module centrifugal spinner filter cap may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto nearby exhaust components. The discharge of engine oil onto hot exhaust components could result in a fire causing property damage and/or personal injury. Correction: Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap.

• Engine#2010329October 4, 2010

  59 units affected

  On certain vehicles, the exhaust gas recirculation (EGR) oil seal installed on the output shaft of the valve actuator may delaminate, possibly allowing engine oil to leak from the EGR valve onto exhaust components. Engine oil leaking onto hot exhaust components, such as when the engine is under significant load, may create the possibility of a fire which can result in personal injury or property damage. Correction: Dealers will replace the EGR valve.

• Steering#2010216June 30, 2010

  774 units affected

  On certain trucks, the weld around the steering shaft tube, which joins the splined tube to the non-splined intermediate tube, may be mislocated. An improperly located weld bead may allow the splined tube and non-splined tube to rotate relative one another during a low speed, high torque turn, resulting in a possible separation of the tubes. This could cause a loss of steering control which could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the steering shaft.

Canadian data updated August 24, 2026