Mitsubishi Outlander recalls

• Structure#2025405August 6, 2025

  62,111 units affected

  Issue: On certain vehicles, water could enter the tailgate struts and cause them to corrode. If this happens, the struts could fail, and the tailgate could drop suddenly. Safety Risk: A tailgate that drops suddenly could increase the risk of injury. Corrective Actions: Mitsubishi will notify owners by mail and advise you to take your vehicle to a dealership to replace the tailgate struts.

• Visual System#2025301May 30, 2025

  68,329 units affected

  Issue: On certain vehicles, a software problem could cause the rearview camera image not to appear on the display screen. Canadian regulations require the rearview image to display when the vehicle is reversing. Note: This recall replaces Transport Canada recall no. 2023-285. Vehicles that were repaired under that recall also require this repair. Safety Risk: A rearview camera image that doesn't display could reduce a driver's ability to see behind the vehicle while backing up. This could increase the risk of a crash. Corrective Actions: Mitsubishi will notify owners by mail and advise you to take your vehicle to a dealership to update the infotainment display software.

• Label#2024554September 19, 2024

  258,000 units affected

  Issue: On certain vehicles, the compliance label may be missing information in French. The words and abbreviations listed on the label for "TIRES", "RIMS", "WITH", "FR" and "RR" and appear in English only, when they should be listed as "TIRES/PNEUS", "RIMS/JANTES", "WITH/AVEC", "FR/AVT" and "RR/ARR". Canadian regulations require this information to be listed on the label in both English and French. Safety Risk: These small errors do not affect vehicle safety. Corrective Actions: This is not a recall. Mitsubishi has corrected the compliance label for all new vehicles.

• Visual System#2023285May 12, 2023

  17,364 units affected

  This recall was replaced by Transport Canada recall no. 2025-301. Issue: On certain vehicles, a software problem could cause the rearview camera image to not appear on the display screen. Canadian regulations require the rearview image to display when the vehicle is reversing. Safety Risk: A rearview camera image that doesn't display could reduce a driver's ability to see behind the vehicle while backing up. This could increase the risk of a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealership to update the display software.

• Visual System#2022351June 30, 2022

  8,583 units affected

  Issue: On certain vehicles, a software problem could cause the rearview camera image not to appear on the display. Canadian regulations require the rearview image to display when the transmission is shifted into reverse gear. Safety Risk: A rearview camera image that does not display could reduce a driver's ability to see behind the vehicle while backing up. This could increase the risk of a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealership to update the infotainment display software.

• Seats And Restraints#2022251May 13, 2022

  493 units affected

  Issue: On certain vehicles, the passenger seat belts may contain defective automatic locking retractors (ALR). As a result, the seat belts may not properly lock to secure a child seat. Note: The vehicle's lower universal anchorage system (UAS) is not affected by this defect and may still be used to secure a child seat. Safety Risk: A seat belt that is used to secure a child restraint but is not properly locked could increase the risk of injury in a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the seat belts for the front passenger seat and the left and right second row seats. They will be replaced, if necessary.

• Fuel System#2022018January 24, 2022

  3,903 units affected

  Issue: On certain vehicles, the fuel pump could fail. If this happens, the engine could stall while driving and you may not be able to restart it. Safety Risk: A sudden loss of engine power while driving could increase the risk of a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to replace the fuel pump.

• Seats And Restraints#2021471July 30, 2021

  355 units affected

  Issue: On certain vehicles, the passenger seat belt assemblies may contain defective automatic locking retractors (ALR). As a result, the seat belts may not properly lock to secure a child seat. Safety Risk: A seat belt that is not properly locked could increase the risk of injury in a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the seat belts. They will be replaced, if necessary.

• Brakes#2020579November 27, 2020

  4,916 units affected

  Issue: On certain vehicles, the parking brake operating shaft in the rear brake caliper could rust and become stuck. If this happens, the parking brake may not work properly. As a result, the brakes could drag or parking brake performance could be reduced. If the vehicle is not left in in gear when it is parked, it could roll away. Note: This is an expansion of recall SR-18-002 (Transport Canada Recall No. 2018-053). Safety Risk: A parked vehicle that rolls away could create the risk of an injury or a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to replace the rear brake calipers.

• Seats And Restraints#2020317July 14, 2020

  45,689 units affected

  Issue: On certain vehicles, the seat belt buckle for the right seat in the second-row could be damaged when the seats are folded down. This can cause the seat belt buckle cover to come off. If this happens, the seat belt may not latch properly. Safety Risk: A seat belt that does not latch properly could create an increased risk of injury in a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to modify the center seat belt buckle in the second seating row. A warning label will also be attached to the right seat base and additional instructions will be added to the owner's manual.

• Structure#2020216May 15, 2020

  81,449 units affected

  Issue: On certain vehicles, road salt can corrode the front cross-member (subframe). As a result, a lower control arm could eventually detach from the cross-member. This could cause a loss of vehicle control. Safety Risk: A loss of control can create the risk of a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the front cross-member (subframe). If no significant corrosion is found, the dealer will spray a sealing and anti-corrosion coating both inside and on the cross-member. If significant corrosion is found, the dealer will replace the cross-member.

• Seats And Restraints#2020215May 15, 2020

  526 units affected

  Issue: On certain vehicles, the right-side seat belt in the second-row seating may have an incorrect guide piece installed. As a result, the seat belt may not work properly in a crash. Safety Risk: A seat belt that does not work properly could increase the risk of injury in a crash. Corrective Actions: Mitsubishi will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the right-side seat belt in the second-row. If the wrong guide piece is installed, the seat belt will be replaced.

• Electrical#2018589October 26, 2018

  7,575 units affected

  On certain vehicles, a wiring connector located under the driver's side carpet may become contaminated by salt water and corrode over time. This could cause a short-circuit that may cause the connector to overheat and melt and potentially lead to a fire if combustible objects are nearby. A vehicle fire could result in injury and/or damage to property. Correction: Dealers will relocate and replace the wiring connector terminal to a higher position and replace the rear display harness with a new one.

• Other#2018508September 14, 2018

  18,281 units affected

  On certain vehicles, an issue in the software that manages the brake system Hydraulic Unit may allow it to reset without warning and could cause some vehicle features to malfunction. If this were to occur while driving, the following features may be affected: automatic braking (if Automatic Cruise Control (ACC) and/or Forward Collision Mitigation (FCM) is in operation), Antilock Brake System (ABS), Active Stability Control (ASC), Brake Auto Hold (BAH). If these systems malfunction, there could be an increased risk of a crash causing injury and/or damage to property. Correction: Dealers will update the Hydraulic Unit control software.

• Other#2018507September 14, 2018

  8,089 units affected

  On certain vehicles, an issue in the software used by the Electronic Control Unit responsible for managing the Forward Collision Mitigation (FCM) feature may cause it to not operate as intended alerting the driver to brake unnecessarily in certain situations. If the driver attempts to brake while FCM is also activating, the vehicle may decelerate rapidly. This could create a situation where another motorist does not anticipate a preceding vehicle’s sudden brake application or stop, creating the risk of a rear-end collision causing injury and/or damage to property. Correction: Dealers will update the software for the Forward Collision Mitigation system.

• Accessories#2018054January 26, 2018

  18,795 units affected

  On certain vehicles, the sunroof may not have been bonded properly and could separate from the vehicle. This could pose a risk to other road users, increasing the risk of injury and/or damage to property. Correction: Dealers will replace the sunroof glass assembly.

• Brakes#2018053January 26, 2018

  39,131 units affected

  On certain vehicles, insufficient rust prevention to the parking brake shaft and insufficient sealing performance of the rear brake caliper boot could allow water to penetrate inside these components causing corrosion. As a result, the parking brake shaft may become stuck causing brake dragging and/or decreased parking brake performance. Additionally, the automatic adjuster for the brake pad clearance of the rear brake caliper with the built-in parking brake may not work correctly. These conditions could lead to a vehicle rollaway, which would increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect and repair the rear brakes as necessary.

• Electrical#2018052January 26, 2018

  45,050 units affected

  On certain vehicles, the flange of the drive belt automatic tensioner may crack over time due to repetitive high load operations and stress concentration. This could cause the drive belt to detach, leading to battery depletion, which would result in a loss of motive power and a loss of power steering assist. These issues could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the auto tensioner with a countermeasure unit.

• Engine#2017475September 29, 2017

  28,615 units affected

  On certain vehicles, defective electrical relays may have been installed in the power distribution center. This could cause various electrical circuits to fail, potentially resulting in engine stalling, reduced engine power, or loss of engine cooling fan function potentially resulting in engine overheating. These issues could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace affected relay(s) with updated parts.

• Visual System#2017364July 20, 2017

  42,283 units affected

  On certain vehicles, water may drain from the windshield cowl area and potentially collect in the area of the wiper motor breathing hole. If the wiper motor is not operating, water could potentially enter the wiper motor through the breathing hole. If this occurs, over time, it could result in corrosion and/or an electrical conduction failure, both of which could result in the wiper motor not operating. If the wiper motor were to stop operating, the windshield wipers would become inoperative, which could limit the driver’s visibility under certain operating conditions which may increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the wiper motor with an upgraded wiper motor that will prevent water intrusion.

• Structure#2017198April 7, 2017

  7,742 units affected

  On certain vehicles, the dimensions of some components in certain door latch mechanisms may be out of specification and may not securely latch in high-temperature conditions. If this occurs and a door mechanism does not securely latch, the door could inadvertently open while the vehicle is in motion, which could increase the risk of injury to a vehicle occupant seated next to the door, or result in damage to property. Correction: Dealers will replace the affected door latches with countermeasure units.

• Visual System#2016529October 27, 2016

  42,283 units affected

  On certain vehicles, water may drain from the windshield cowl area onto the front wiper link ball joint. Over time, this could result in corrosion and/or wear to the joint, which could result in the separation of the wiper link ball. If separation were to occur, the windshield wipers could become inoperative, which could limit the driver’s visibility under certain operating conditions which may increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the rubber boot which covers the ball joint with a countermeasure one, and the wiper motor crank arm will also be inspected and replaced as necessary.

• Powertrain#2016379July 27, 2016

  10,833 units affected

  On certain vehicles equipped with a continuously variable transmission (CVT), the range switch could momentarily experience a loss of signal. If this occurs, the driver may experience an unexpected reduction of vehicle acceleration which could, in conjunction with traffic, road conditions and the driver's reactions, increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will reprogram the CVT-ECU.

• Structure#2016317June 21, 2016

  64,305 units affected

  On certain vehicles, road salt can corrode the front crossmember assembly, which may ultimately lead to separation of the control arm at the mounting point. This would allow the wheel to rotate off its designed axis, and could result in a loss of vehicle control and a crash causing property damage and/or personal injury. Correction: Dealers will inspect the crossmember and apply an anti-corrosion treatment or replace the assembly, as required.

• Heater And Defroster#2015166April 17, 2015

  32,810 units affected

  On certain vehicles, the blower motor may have been incorrectly manufactured. This could result in a premature failure of the blower motor which could affect the defroster performance resulting in reduced visibility, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace blower motor and the power transistor as needed.

• Lights And Instruments#2015165April 17, 2015

  27,277 units affected

  On certain vehicles, the ECU which controls the head lights, tail lights and windshield wipers may have been improperly manufactured. This could cause the voltage in the ECU to become unstable and cause the head lights and/or tail lights to turn off and/or the windshield wipers to become inoperable. This could affect driver visibility and decrease vehicle conspicuity, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect and replace the affected ECU with an updated version.

• Engine#2014397September 15, 2014

  49,227 units affected

  On certain vehicles, the drive belt material may cause abnormal pulley wear. If the vehicle is driven under this condition, the drive belt may become damaged from the worn pulley and detach, affecting electrical charging system and cooling system function and would illuminate the engine warning lamp(s) on the instrument panel. This could result in battery depletion and an overheated engine, resulting in a loss of motive power. Vehicles equipped with a hydraulic power steering system could also experience loss of power steering assist. These issues could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the drive belt, and the pulley will be replaced if it is found worn beyond a certain level.

• Powertrain#2014248June 25, 2014

  3,549 units affected

  On certain 2012 to 2014 model year vehicles, due to improper manufacturing of the oil seal boss in certain transfer assemblies, the oil seal can become out of position and allow automatic transmission fluid to enter into the transfer assembly, resulting in reduced automatic transmission fluid pressure in the transaxle. This condition would illuminate the “Automatic Transmission” (A/T) warning light in the instrument panel and could result in the inability to shift gears or to drive the vehicle, increasing the risk of crash causing injury and/or property damage. Correction: Dealers will inspect and, if necessary, replace the transfer assembly. Note: Only a limited number of 2007 to 2010 model year vehicles equipped with a replacement transfer assembly are included in the recall population.

• Steering#2014247June 25, 2014

  1,635 units affected

  Certain 2013 model year vehicles with a 6-speed automatic transmission may have been manufactured with insufficient clearance between the power steering pressure tube and the bosses on the converter housing of the automatic transaxle. This may cause the power steering pressure tube to rust from abrasive contact between the two components. In the worst case, a pin hole could develop and allow for power steering fluid leakage, which can result in the loss of power steering assist and increase the risk of crash causing injury and/or property damage. Correction: Dealers will replace the power steering pressure tube and return tube. Note: Only a limited number of 2007 to 2012 model year vehicles equipped with a replacement automatic transaxle with the bosses on the converter housing are included in the recall population.

• Lights And Instruments#2012001January 4, 2012

  2,301 units affected

  Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 108 - Lighting System and Retroreflective Devices. An incorrectly manufactured turn signal lever could cause the auto-cancel function to become inoperative. The vehicle operator will, however, continue to be able to manually cancel the turn signals. Correction: Dealers will inspect and, if necessary, replace the turn signal lever.

Canadian data updated August 24, 2026