2015 Kenworth T800 recalls

• Structure#2020551November 12, 2020

  91 units affected

  Issue: On certain trucks, the welds that attach the trailer hitch may crack due to improper welding. As a result, the hitch could detach from the truck while towing a trailer. Note: This recall only affects certain trucks with trailer hitches installed by Commercial Truck Equipment. Safety Risk: A trailer that detaches from a truck could create a risk of a crash. Corrective Actions: Commercial Truck Equipment will notify owners by mail and instruct you to take your truck to a dealer to inspect the trailer hitch and repair or replace it, as necessary. You should stop using the trailer hitch until the inspection and repair have been completed.

• Lights And Instruments#2020148April 7, 2020

  65,284 units affected

  Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).

• Brakes#2018389July 24, 2018

  214 units affected

  Certain vehicles may fail to conform to the requirements of Canada Motor Vehicle Safety Standard (CMVSS) 121 - Air Brake Systems and CMVSS 136 - Electronic Stability Control Systems for Heavy Vehicles. In the event that the anti-lock brake system (ABS) loses battery and/or ignition power to the controller, the ABS indicator lamp may not illuminate to warn the driver of the loss of ABS, which is contrary to the requirements of the standards. This could result in the loss of ABS function with no warning to the driver, which could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will reprogram the cab control module.

• Accessories#2017590November 30, 2017

  19 units affected

  On certain fire trucks, the retaining ring(s) in the relief valve assembly may not have been made using high grade stainless steel, causing it to deteriorate over time due to frequent exposure to water. If the retaining ring fails, the relief valve may break down and prevent the fire pump from building adequate pressure, which would increase the risk of injury during firefighting operations. Correction: Dealers or certified technicians will inspect and replace the retaining ring(s) as necessary.

• Brakes#2017267May 18, 2017

  13 units affected

  Certain vehicles equipped with Neway ADZ Tridem rear suspension may not comply with the brake timing requirements of Canada Motor Vehicle Safety Standard (CMVSS) 121 - Air Brake Systems. The brake control airline between the two relay valves is plumbed with a 3/8" airline but should be plumbed with a 1/4" line to balance the service brake application timing and meet the requirement of the standard. An oversized airline could cause a delay in brake activation and increase stopping distances, which could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will update and modify the brake piping of the air brake system.

• Engine#2015211May 15, 2015

  169 units affected

  On certain vehicles equipped with Cummins Westport ISL-G engines, excessive engine crankcase pressure could cause the vent tube assembly elbow to detach from the breather. This could allow engine oil to come in contact with hot surfaces, increasing the risk of fire resulting in injury and/or damage to property. Correction: Dealers will install clamps at both ends of the elbow of the breather tube assembly and reprogram the Electronic Control Module (ECM) to improve diagnostic capabilities.

• Electrical#2015190May 8, 2015

  22,815 units affected

  On certain vehicles, water could migrate into wiper motor head and could lead to internal corrosion. This internal corrosion could form a conductive salt bridge which could result in a short circuit, causing the wiper system to fail. Loss of windshield wiping capability, should it occur during a rainy/snowy day, may compromise the driver's ability to see the road and its users, and a short circuit could increase the risk of fire, which could result in injury and/or damage to property. Correction: Dealers will install a shield over the wiper motor to protect it from water intrusions and prevent corrosion.

• Brakes#2014590December 23, 2014

  218 units affected

  On certain vehicles, brake chamber diaphragm(s) may not be properly seated. This could lead to brake drag, causing brake overheating or unintended spring brake application. These issues could increase the risk of a crash causing injury and/or property damage. Correction: Dealers will replace the brake chambers.

• Electrical#2014512November 7, 2014

  388 units affected

  On certain vehicles, an undersized wire in the trailer stop lamp circuit of the instrument panel harness is susceptible to thermal cycling which may cause damage to the wiring. This could result in the trailer lamp fuse failing, which could cause stop lamps to become inoperative and increase the risk of a crash. This damaged wiring could also increase the risk of fire. These issues could result in injury and/or damage to property. Correction: Dealers will replace the undersized wire in the harness.

• Engine#2014046February 19, 2014

  82 units affected

  On certain vehicles equipped with Cummins ISL G or ISX12 G engines, incorrect engine ECU programming could cause the exhaust system temperature to become elevated during cold weather operation. This could also cause flames to be emitted from the exhaust. As a result, nearby combustible material could be ignited, increasing the risk of a fire, injury and/or damage to property. Correction: Authorized Cummins service facilities will update software programming.

Canadian data updated August 24, 2026

• SERVICE BRAKES, AIR:SUPPLY:RESERVOIR/TANK#24V145000February 23, 2024

  PACCAR Incorporated (PACCAR) is recalling certain 2009-2021 Kenworth C500, 2012-2021 Kenworth T440, 2009-2015 Kenworth T660, 2015-2024 Kenworth T680, 2009-2024 Kenworth T800, 2009-2020 Kenworth T370, 2014-2023 Kenworth T880, 2011-2016 Kenworth T470, 2023 Kenworth T480, and 2009-2019 Kenworth W900 vehicles. The air tanks have an insufficient volume of air for the brake system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems."

  Risk: Insufficient air volume can reduce braking performance and increase the risk of a crash.

  Remedy: Dealers will install the correct volume air tanks, free of charge. Owner notification letters were mailed August 12, 2024. Additional owner notification letters were mailed October 27, 2025. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 24KWD.

• ELECTRONIC STABILITY CONTROL (ESC)#20V199000April 6, 2020

  PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

  Risk: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

• ELECTRONIC STABILITY CONTROL (ESC)#18V368000June 1, 2018

  PACCAR Incorporated (PACCAR) is recalling certain 2017-2018 Peterbilt 567 and 579 trucks and 2015-2018 Kenworth T660, T680, T800, T880 and W900 trucks. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

  Risk: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on July 30, 2018. Owners may contact Peterbilt customer service at 1-918-259-3258 or Kenworth customer service at 1-425-828-5000.

• EQUIPMENT#17V739000November 20, 2017

  E-One Incorporated (E-One) is recalling certain 2013-2017 E-One Cyclone II, Quest, Typhoon, 2016 Freightliner M2 112, 2013-2015 International 7400, 2014-2017 International 4400, Freightliner M2 106, 2016-2017 Kenworth T370, and 2015 Kenworth T800 vehicles equipped with Hale pressure relief valves in the water pumps used for fire fighting. Rings securing the valves may corrode over time after exposure to water, causing the ring to fail and the pressure relief valve to open, reducing the water pressure available for fire fighting.

  Risk: A reduction in water pressure may hinder fire fighting efforts, increasing the risk of injury.

  Remedy: E-One will notify owners, and a certified dealer or technician will install a stainless steel retaining ring, free of charge. The recall began on January 11, 2018. Owners may contact E-One customer service at 1-352-861-3612.

• SERVICE BRAKES, AIR#17V322000May 16, 2017

  PACCAR Incorporated (PACCAR) is recalling certain 2012-2018 Kenworth T800 and T880 vehicles equipped with Neway ADZ tridem rear suspensions. The brake control airline may be the incorrect size, resulting in an imbalance in the service brake application timing. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air brake systems."

  Risk: An incorrectly sized airline may lengthen the distance needed to stop the vehicle, increasing the risk of a crash.

  Remedy: Kenworth will notify owners, and dealers will modify the air brake system with updated brake piping, free of charge. The recall began on June 21, 2017. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 17KWB.

• POWER TRAIN:DRIVELINE:DRIVESHAFT#15V310000May 26, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2014 and 2015 Kenworth T660, T680, and T800 trucks manufactured January 29, 2013, to April 2, 2014, and 2013 Peterbilt 587 trucks manufactured on August 8, 2012. The affected trucks are built with a driveshaft that may not transmit power to the wheels due to weld failure from corrosion.

  Risk: If the weld fails causing a loss of power to the rear wheels, the vehicle operator may be unable to move the vehicle, or may experience deceleration if the vehicle is in motion, increasing the risk of a vehicle crash.

  Remedy: PACCAR will notify owners, and dealers will replace the defective driveshafts, free of charge. The recall began on July 15, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, or Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 15KWJ and 515-H.

• ENGINE AND ENGINE COOLING:ENGINE#15V309000May 26, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.

  Risk: If engine oil comes into contact with a hot surface, there is an increased risk of a fire.

  Remedy: Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.

• VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR#15V271000May 8, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2011-2016 Kenworth T270, T370, T440, T470, C500, C540, C550, T660, T800, W900, and 963 trucks manufactured November 1, 2010, to April 6, 2015. In the affected trucks, water may leak into the wiper motor.

  Risk: As water leaks in, the wiper may cease to function on the 'intermittent' setting, reducing the driver's visibility and increasing the risk of a crash. Additionally, the water may cause corrosion which, over time, may result in an electrical short, increasing the risk of a fire.

  Remedy: PACCAR is still developing and testing a remedy. The recall is expected to begin in July 2015. An interim letter was sent to owners on July 2, 2015. The recall began on September 2, 1015. Owners may contact Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 15KWF.

• SERVICE BRAKES, AIR:DISC:CALIPER#15V051000January 30, 2015

  PACCAR Incorporated (PACCAR) is recalling certain model year 2015 Peterbilt 210, 220, 320, and Kenworth K270, K370, T660, T800, T880 trucks manufactured July 21, 2014, to September 16, 2014. The brake caliper bolts may not be properly torqued.

  Risk: As a result, the brake caliper bolts may loosen, reducing the effectiveness of the brakes and increasing the risk of a crash.

  Remedy: PACCAR will notify owners, and dealers will inspect, and tighten or replace any loose caliper bolts, as necessary, free of charge. The recall began on March 27, 2015. Owners may contact Peterbilt customer service 1-940-591-4000, or Kenworth customer service at 1-425-828-5000. PACCAR's number for this recall is 15KWA (Kenworth) and 115B (Peterbilt).

• PARKING BRAKE:CONVENTIONAL:AIR#14V810000December 29, 2014

  PACCAR Incorporated (PACCAR) is recalling certain model year 2015 Peterbilt 367, 389, 567, 579, and 587 trucks manufactured from May 23, 2014, to February 13, 2015, and 2015 Kenworth T270, T370, T440, T470, T660, T680, T800, T880, and W900 trucks manufactured from May 23, 2014, to February 13, 2015, equipped with certain air brake actuators. The affected vehicles may experience brake drag due to an improperly seated diaphragm in the brake chamber.

  Risk: Brake drag may result in a wheel end fire.

  Remedy: Kenworth and Peterbilt will notify owners, and dealers will inspect and replace the brake chamber, as necessary, free of charge. An interim notice was mailed to owners March 3, 2015. The recall began on May 14, 2015. Owners may contact PACCAR customer service at 1-425-828-5000 (Kenworth), or 1-940-591-4000 (Peterbilt). PACCAR's number for this recall is 14KWP (Kenworth), and 1214L (Peterbilt).

• ELECTRICAL SYSTEM#14V722000November 10, 2014

  PACCAR Incorporated (PACCAR) is recalling certain model year 2015 Kenworth T660, T800, W900, T400, and C500 heavy trucks manufactured September 19, 2014, to October 30, 2014. The affected vehicles may have been produced with an undersized wire gauge for the trailer stop lamp circuit in the instrument panel harness.

  Risk: If the smaller wire gauge may overheat increasing the risk of a vehicle fire.

  Remedy: PACCAR will notify owners, and dealers will replace the defective wire with a properly sized wire, free of charge. The recall began on December 19, 2014. Owners may contact PACCAR customer service at 1-425-828-5000 (Kenworth).

• ENGINE AND ENGINE COOLING:ENGINE#14V086000February 18, 2014

  PACCAR Inc, is recalling certain model year 2014-2015 Kenworth T440, T660, T800, and W900 tractor trailers manufactured January 23, 2013, through February 4, 2014, and certain model year 2014-2015 Peterbilt 320, 365, 382, 384 tractor trailers manufactured January 21, 2013, through February 5, 2014, and equipped with certain Cummins Westport Model ISL G and ISX12 G engines. Condensation in the intake manifold may freeze during cold weather conditions and interfere with the proper operation of the intake manifold pressure sensor.

  Risk: The improper operation of the sensor could induce elevated exhaust temperatures or flames from the exhaust pipe, increasing the risk of a vehicle fire or burn injury to a person near the exhaust pipe.

  Remedy: PACCAR will notify owners, and authorized Cummins service facilities will upload a new ECM calibration, free of charge. The recall began on April 12, 2014. Customers may contact PACCAR at 1-425-468-7400. Paccar's recall numbers associated with this campaign are 14KWG (Kenworth), and 214-C (Peterbilt).