2015 GMC Sierra recalls

• Electrical#2024294May 24, 2024

  4,699 units affected

  Issue: On certain trucks, the repairs completed by a General Motors dealer during recall N192220470 (Transport Canada recall no. 2019-325) or customer satisfaction program no. N192270330 may not have been completed properly. As a result, a second repair is required. Additionally, certain trucks may not have had the updated parts installed during production. On certain trucks equipped with a power sliding rear window, the rear defroster wiring could overheat and melt. Safety Risk: Wiring that overheats and melts can create the risk of a fire. Corrective Actions: General Motors will notify owners by mail and advise you to take your truck to a dealership to replace the contact cover for the sliding rear window. The dealer will also update the heating, ventilation, and air conditioning (HVAC) software, if necessary. If the rear window or sliding glass assembly are damaged, they will be replaced.

• Airbag#2021410July 1, 2021

  34,366 units affected

  Issue: On certain trucks, the side curtain airbag inflators could be defective. As a result, the driver and/or passenger side curtain airbag inflator(s) could fail. If this happens, the end cap from the inflator or other parts could be propelled into the vehicle and strike a person. Note: This recall replaces Transport Canada Recall No. 2020-576. Safety Risk: A metal end cap or other parts that strike a person could create a risk of injury. Corrective Action: General Motors will notify owners by mail and instruct you to take your truck to a dealer to replace both side curtain airbags.

• Seats And Restraints#2021212April 9, 2021

  249 units affected

  Issue: On certain vehicles, the flexible steel cable that connects the seat belt to the outboard side of the driver's seat may have been replaced with an incorrect part during a previous repair. Over time, this cable could flex and may eventually break. If this happens, the seat belt could detach in a crash. Note: This recall only affects certain vehicles that had the driver's seat belt pretensioner replaced after a previous recall repair (recall 2016-153 or 2018-233). Safety Risk: A seat belt that detaches in a crash could increase the risk of injury. Corrective Actions: General Motors will notify owners by mail and instruct you to take your vehicle to a dealer to replace the driver's outboard seat belt pretensioner assembly.

• Airbag#2020576November 25, 2020

  767 units affected

  This recall was replaced by Transport Canada Recall No. 2021-410. Issue: On certain trucks, the side curtain airbag inflators could be defective. As a result, the driver and/or passenger side curtain airbag inflator(s) could fail. If this happens, the end cap from the inflator could be propelled into the vehicle and strike a person. Safety Risk: A metal end cap that strikes a person could create a risk of injury. Corrective Actions: General Motors will notify owners by mail and instruct you to take your truck to a dealer to replace one or both of the side curtain airbag(s).

• Brakes#2019533October 24, 2019

  37,378 units affected

  Issue: On certain vehicles, there may be an error in the electronic-brake control module software. This could cause the driveline-protection system to activate when a wheel-speed sensor fails. If this happens, the brakes could apply and cause the vehicle to pull to one side. Note: This recall only affects vehicles equipped with four-wheel drive, a 5.3-L engine, and a 3.08 ratio rear axle. The problem can only occur when the vehicle is in four-wheel drive or automatic mode, and travelling at a speed between 66 and 97 km/h (41 and 60 mph). A wheel-speed sensor failure will cause the electronic stability control (ESC) and anti-lock braking system (ABS) warning lights to turn on, and a "Service StabiliTrak" message to display. Safety Risk: A vehicle that suddenly pulls to one side could increase the risk of a crash. Corrective Actions: General Motors will notify owners by mail and instruct you to take your vehicle to a dealer to update the electronic-brake control module software. General Motors advises that using two-wheel-drive mode can eliminate the risk until the recall repair is completed.

• Other#2019420August 21, 2019

  5,327 units affected

  Issue: This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones. Note: This is a voluntary recall that is not being conducted under the requirements of the Motor Vehicle Safety Act. Safety Risk: Glass that breaks in to large pieces could create a risk of injury. Corrective Actions: The company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “DOT 287” along with the lettering “VMR” (Replacement Market) and a date code that is before July 2019. This information is printed on the bottom corner of the glass. Consumers should contact Vitro's customer service at 1-412-995-6457 or argbacklites@vitro.com to arrange for replacement of the glass.

• Electrical#2019325June 28, 2019

  159,474 units affected

  Issue: On certain trucks equipped with a power sliding rear window, the rear defroster circuit could overheat. This could cause melting, smoke or, in rare instances, a fire. Safety Risk: A fire could create a risk of injury. Corrective Actions: The company will notify owners by mail and advise you to take your truck to a dealer to replace the covers for the buss bar and contacts for the rear sliding window. If the rear window or sliding glass assembly are damaged due to a problem with the rear defroster, they will also be replaced.

• Brakes#2019324June 28, 2019

  310,121 units affected

  Issue: On certain vehicles, there could be a reduction in power brake assist due to a decrease in output from the vacuum pump. This could cause a hard brake pedal and an increase in brake pedal effort to stop the vehicle. Safety Risk: A sudden increase in brake pedal force could lead to an increase in stopping distance. This could increase the risk of a crash. Corrective Actions: The company will notify owners by mail and instruct them to take their vehicle to a dealer to reprogram the electronic brake control module.

• Steering#2018482September 7, 2018

  95,832 units affected

  Certain vehicles may experience a temporary loss of electric power steering (EPS) assist followed by a sudden return of EPS assist, particularly during low-speed turning manoeuvres due to an electrical/software issue. If EPS assist is lost and suddenly returned, the unexpected change in steering effort could affect vehicle control, which would increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will update the EPS module software. Note: If power steering assist is lost and the vehicle reverts to manual steering, a dash message would be displayed stating there is an EPS problem. Additionally, this issue could also affect radio, stabilitrak, the driver information centre, chime, door-lock, air conditioning, and/or cruise control function.

• Brakes#2018464August 31, 2018

  3,348 units affected

  Certain Heavy Duty and Police/Special Service vehicles may not have been repaired properly under Recall 2016-053 (GM #20760). The brake pedal pivot nut may become loose, causing the brake pedal to be loose or inoperative. If this happens, a driver may be unable to safely stop the vehicle or the brake pedal may interfere with the accelerator pedal. Both of these situations could increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will add adhesive to the pivot nut and will reinstall it at an increased torque. Note: This condition may result in the "Service Engine Soon" light illuminating, and brake lights may stay on longer than expected.

• Fuel System#2017511October 20, 2017

  1,908 units affected

  On certain vehicles equipped with gasoline engines and dual fuel tanks, the fuel level sensor in the front tank could become stuck in the low level position, causing the rear tank to overfill the front tank. If this occurs, the front tank could expand and come in contact with the moving drive shaft which, over time, could create a hole in the front tank and cause a fuel leak. A fuel leak in the presence of an ignition source could result in a fire causing injury and/or damage to property. Correction: Dealers will replace the rear tank fuel pump module or flash the vehicle software. Dealers will also inspect the front tank for damage and replace it as necessary.

• Airbag#2017342July 10, 2017

  152 units affected

  On certain vehicles, the sensing and diagnostic module (SDM), which controls airbag and pretensioner deployment, contains a software defect which may prevent the deployment of frontal airbags and pretensioners in certain circumstances. Failure of frontal airbags and seatbelt pretensioners to deploy in a crash (when warranted) could increase the risk of injury. Correction: Dealers will reflash the SDM with new software. In vehicles with any previous deployment events recorded in the SDM, the dealers will replace the existing SDM with a new SDM containing the latest software.

• Airbag#2016439September 9, 2016

  362,263 units affected

  On certain vehicles, the sensing and diagnostic module (SDM), which controls airbag and pretensioner deployment, contains a software defect which may prevent the deployment of frontal airbags and pretensioners in certain circumstances. Failure of frontal airbags and seatbelt pretensioners to deploy in a crash (when warranted) could increase the risk of injury. Correction: Dealers will reflash the SDM with new software. In vehicles with any previous deployment events recorded in the SDM, the dealers will replace the existing SDM with a new SDM containing the latest software. Note: This recall affects 2014-2017 model year Sierra LD/Silverado LD models and 2015-2016 model year Sierra HD/Silverado HD model vehicles.

• Seats And Restraints#2016153April 11, 2016

  108,604 units affected

  On certain Sierra 1500 and Silverado 1500 vehicles, the flexible steel cable that connects the driver's seat belt to the vehicle structure at the outboard position can fatigue over time and could separate, increasing the risk of injury in a crash. Correction: Dealers will enlarge the side shield opening, install a pusher bracket on the tensioner and, if necessary, replace the tensioner assembly.

• Brakes#2016053February 4, 2016

  47,148 units affected

  On certain Heavy Duty and Police Pursuit vehicles, the brake pedal pivot nut may become loose, causing the brake pedal to be loose or inoperative. If the brake pedal becomes loose or inoperative, it could interfere with the accelerator pedal, and/or the driver may be unable to safely stop the vehicle through application of the brake pedal, potentially affecting stopping distances and increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the pivot bolt installation to determine whether the vehicle has already received the production remedy. If not, the dealer will add adhesive to the nut, and reinstall the nut at an increased torque. Note: This condition may result in the "Service Engine Soon" light illuminating, and brake lights may stay on longer than expected.

• Electrical#2015458October 8, 2015

  138 units affected

  On certain vehicles, a defect in the ignition lock actuator may make turning the ignition key difficult or cause the key to get stuck in the “start” position. This may be more likely to occur at higher interior ambient temperatures. If the vehicle is driven with the key stuck in the “start” position, and the vehicle experiences a significant jarring event or the vehicle’s interior temperature cools, the ignition key could move out of the “start” position, rotate past the “run” position, and move into the “accessory” position, causing the engine to shut off. This would result in a loss of motive power and affect power steering and power brake system function, which could increase the risk of a crash causing injury and/or damage to property. The timing of the key movement out of the “run” position, relative to the activation of the sensing algorithm in a crash event, may also result in the airbags not deploying in a subsequent collision, increasing the risk of injury. Correction: Dealers will replace the ignition lock housing.

• Powertrain#2014589December 22, 2014

  15 units affected

  On certain vehicles, rear axle shafts may not have been properly heat treated. An improperly heat-treated axle shaft could fracture without warning near the hub flange resulting in separation of a rear wheel from the axle shaft, increasing the risk of a crash which may result in injury and/or property damage. Correction: Dealers will inspect the manufacturing code on rear axle shafts and replace those identified as defective.

• Fuel System#2014588December 22, 2014

  11 units affected

  On certain vehicles equipped with diesel engines, a hose clamp for the fuel tank vent line may not have been sufficiently tightened at assembly. This could allow the vent line to become detached from the fuel tank, which could cause a fuel leak. Fuel leakage, in the presence of an ignition source, could result in a fire causing injury and/or damage to property. Correction: Dealers will inspect and tighten the clamp as necessary.

• Engine#2014577December 18, 2014

  10 units affected

  On certain vehicles, exhaust components may overheat while the vehicle is idling in cold temperatures. This could cause nearby plastic components to overheat and melt, possibly resulting in smoke and/or fire and increasing the risk of injury and/or damage to property. Correction: Dealers will reprogram the engine control module. Note: This is an expansion of recall 2014-005.

• Steering#2014509November 7, 2014

  112 units affected

  Certain vehicles may experience a sudden loss of power steering assist that could occur at any time while driving. If the power steering assist is lost, a message is displayed on the Driver Information Centre and a chime sounds to inform the driver. Steering control can be maintained, as the vehicle will revert to a manual steering mode, but will require greater driver effort particularly at low vehicle speeds. The sudden change in steering may increase the risk of a crash causing injury and/or property damage. Correction: Dealers will replace the power steering assist motor.

• Steering#2014443October 7, 2014

  8,778 units affected

  On certain model 2500/3500 HD vehicles, power steering hose clamps may not have been properly attached. This could allow the hose to disconnect from the power steering pump or steering gear, causing a power steering fluid leak. This would result in a loss of power steering assist and hydraulic assist brakes, unexpectedly increasing steering and brake pedal effort and potentially increasing stopping distances and the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the clamps to ensure they are properly attached. Note: This is an expansion of recall 2014-241.

• Powertrain#2014254June 27, 2014

  53,607 units affected

  Certain vehicles equipped with an Automatic Transfer Case may have a condition in which an electric signal short may cause the transfer case to switch to neutral without operator input. The transfer case mode selection knob would still indicate the last selected drive mode, but the driver would not have any feedback that the transfer case is in neutral. If the transfer case switches to neutral while the vehicle is in motion, the driver would experience a loss of motive power and, if the vehicle is parked without the parking brake applied, the vehicle could roll away. Both scenarios could result in a crash causing injury and/or damage to property. Correction: Dealers will re-program the software of the Transfer Case Control Module.

• Steering#2014241June 19, 2014

  6,778 units affected

  On certain model 2500/3500 HD vehicles, power steering hose clamps may not have been properly attached. This could allow the hose to disconnect from the power steering pump or steering gear, causing a power steering fluid leak. This would result in a loss of power steering assist and hydraulic assist brakes, unexpectedly increasing steering and brake pedal effort and potentially increasing stopping distances and the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the clamps to ensure they are properly attached.

• Accessories#2014216June 6, 2014

  5,439 units affected

  Certain vehicles equipped with a base radio and internal amplifier may fail to conform to Canada Motor Vehicle Safety Standard (CMVSS) 114 - Theft Protection and Rollaway Protection, and CMVSS 208 - Occupant Crash Protection. The radio may become inoperative, causing a no-chime condition and disabling the audible warning if the key is in the ignition and the driver’s door is opened, or if a front outboard seat belt is not buckled. A loss of the seat belt audible warning may increase the likelihood of a front outboard occupant being unbelted, increasing the risk of injury in a crash. Similarly, the loss of an audible warning when a key is left in the ignition may increase the risk of vehicle theft. Correction: Dealers are to program the radio with updated software.

• Airbag#2014206June 4, 2014

  9 units affected

  On certain vehicles, an internal fault in the Sensing and Diagnostic Module may set a diagnostic trouble code, illuminating the airbag warning lamp and disabling the airbags and seatbelt pretensioners for the duration of the drive cycle. This could increase the risk of injury in a crash. Correction: Not applicable. NOTE: Further analysis has shown that no defect existed in the Sensing and Diagnostic Module, and that this recall is therefore inactive.

• Fuel System#2014153April 25, 2014

  8 units affected

  On certain HD vehicles equipped with a diesel engine and dual fuel tanks, the fuel pipe tube nuts on each side of the diesel fuel transfer pump may not have been properly torqued. As a result, diesel fuel may leak at the fuel transfer pump if there is fuel in the rear tank and the transfer pump activates to transfer fuel to the forward fuel tank. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or injury. Correction: Dealers will tighten the tube nuts to the proper torque.

Canadian data updated August 24, 2026

• ELECTRICAL SYSTEM:IGNITION#15V640000October 9, 2015

  General Motors LLC (GM) is recalling certain model year 2014-2015 Chevrolet Silverado and GMC Sierra trucks manufactured January 24, 2014, to February 26, 2014, 2015 Chevrolet Suburban vehicles manufactured February 12, 2014 and Chevrolet Tahoe vehicles manufactured February 6, 2014, to February 13, 2014. In the affected vehicles, the ignition lock actuator may bind, making turning the key difficult or causing the ignition to get stuck in the "Start" position.

  Risk: If stuck in the "Start" position, the ignition may suddenly snap back into the "Accessory" position, causing a loss of engine, steering, and braking power, increasing the risk of a vehicle crash. If the vehicle is in a crash, the air bags may not deploy, increasing the risk of occupant injury.

  Remedy: GM will notify owners, and dealers will replace the ignition lock housing, free of charge. The recall began on November 20, 2015. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 15573.

• POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT#14V819000December 24, 2014

  General Motors LLC (GM) is recalling certain model year 2015 Chevrolet Silverado 1500, and GMC Sierra 1500 vehicles manufactured November 24, 2014, to November 25, 2014. Due to an improper heat-treatment, the rear axle shaft may fracture while the vehicle is being driven.

  Risk: If the rear axle shaft fractures, the rear wheel may separate from the axle shaft, increasing the risk of a crash.

  Remedy: GM will notify owners, and dealers will inspect the rear axles, and replace any that were improperly heat-treated, free of charge. The recall began on December 17,2014. Owners may contact GM customer service at 1-800-222-1020 (Chevrolet) or 1-800-462-8782 (GMC). GM's number for this recall is 14892.

• STEERING:ELECTRIC POWER ASSIST SYSTEM#14V719000November 10, 2014

  General Motors LLC (GM) is recalling certain model year 2015 Chevrolet Silverado, Suburban, Tahoe, GMC Sierra, and Yukon XL vehicles, equipped with electric power steering (EPS). Due to a problem with the EPS module, the affected vehicles may experience a sudden loss of power steering assist during vehicle operation.

  Risk: An unexpected loss of power steering increases the risk of a crash.

  Remedy: GM will notify owners, and dealers will replace the power steering assist motor kit, free of charge. The recall began on November 17, 2014. Owners may contact GM customer service at 1-800-222-1020 (Chevrolet), or 1-800-462-8782 (GMC). GM's number for this recall is 14743.

• SEATS#14V446000July 23, 2014

  General Motors LLC (GM) is recalling certain model year 2013-2014 Buick Encore and Cadillac ATS; 2014 Cadillac CTS, ELR, Chevrolet Caprice and SS vehicles; and 2014-2015 Chevrolet Silverado and GMC Sierra Trucks. Due to an incomplete weld on the seat hook bracket assembly, the front seats in the affected vehicles may not stay secured in place during a high load condition such as a crash.

  Risk: A seat that does not stay secured increases the risk of occupant injury in a vehicle crash.

  Remedy: GM will notify owners, and dealers will inspect the seat hook bracket assembly weld and replace the lower seat track, as necessary, free of charge. The recall began on August 15, 2014. Owners may contact GM customer service at 1-800-521-7300 (Buick), 1-800-458-8006 (Cadillac), 1-800-222-1020 (Chevrolet), and 1-800-462-8782 (GMC). GM's number for this recall is 14340.

• POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE)#14V374000June 27, 2014

  General Motors LLC (GM) is recalling certain model year 2014-2015 Chevrolet Silverado and GMC Sierra vehicles, and model year 2015 GMC Yukon and Chevrolet Suburban and Tahoe vehicles. In the affected vehicles, an electrical signal short may cause the transfer case to shift to neutral without the driver's input.

  Risk: If the transfer case switches to neutral while the vehicle is parked and the parking brake is not in use, the vehicle may roll away increasing the risk of injury to bystanders. If the transfer case switches to neutral while the vehicle is being driven, the vehicle would lose drive power, increasing the risk of a crash.

  Remedy: GM will notify owners, and dealers will re-program the software in the transfer case control module, free of charge. The recall began in early August 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), or 1-800-462-8782 (GMC). GM's number for this recall is 14192.

• ENGINE AND ENGINE COOLING:EXHAUST SYSTEM#14V007000January 13, 2014

  General Motors is recalling certain 2014 model year Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles, and 2015 model year Cadillac Escalade and Escalade ESV; Chevrolet Silverado HD; and GMC Sierra HD, Yukon, and Yukon XL, equipped with a 4.3L engine or 5.3L engine.

  Risk: The overheated exhaust components may melt nearby plastic parts and may result in an engine fire.

  Remedy: General Motors will notify owners, and dealers will reprogram the engine control module, free of charge. The recall began on January 16, 2014. Owners may contact Chevrolet at 1-800-222-1020 and GMC at 1-800-462-8782. General Motors' number for this recall is 14008.