Skip to content
VINscan

RECALLS — MAKE · MODEL · YEAR

2016 GMC Sierra 2500 recalls

16 safety recall campaigns have been filed for the 2016 GMC Sierra 2500 with Transport Canada and the U.S. NHTSA. Here is what both agencies say.

Canadian recalls
11
U.S. recalls
05
Total campaigns
16

Transport Canada recalls

11
  • Electrical#2024294

    4,699 units affected

    Issue: On certain trucks, the repairs completed by a General Motors dealer during recall N192220470 (Transport Canada recall no. 2019-325) or customer satisfaction program no. N192270330 may not have been completed properly. As a result, a second repair is required. Additionally, certain trucks may not have had the updated parts installed during production. On certain trucks equipped with a power sliding rear window, the rear defroster wiring could overheat and melt. Safety Risk: Wiring that overheats and melts can create the risk of a fire. Corrective Actions: General Motors will notify owners by mail and advise you to take your truck to a dealership to replace the contact cover for the sliding rear window. The dealer will also update the heating, ventilation, and air conditioning (HVAC) software, if necessary. If the rear window or sliding glass assembly are damaged, they will be replaced.

  • Airbag#2021410

    34,366 units affected

    Issue: On certain trucks, the side curtain airbag inflators could be defective. As a result, the driver and/or passenger side curtain airbag inflator(s) could fail. If this happens, the end cap from the inflator or other parts could be propelled into the vehicle and strike a person. Note: This recall replaces Transport Canada Recall No. 2020-576. Safety Risk: A metal end cap or other parts that strike a person could create a risk of injury. Corrective Action: General Motors will notify owners by mail and instruct you to take your truck to a dealer to replace both side curtain airbags.

  • Brakes#2019533

    37,378 units affected

    Issue: On certain vehicles, there may be an error in the electronic-brake control module software. This could cause the driveline-protection system to activate when a wheel-speed sensor fails. If this happens, the brakes could apply and cause the vehicle to pull to one side. Note: This recall only affects vehicles equipped with four-wheel drive, a 5.3-L engine, and a 3.08 ratio rear axle. The problem can only occur when the vehicle is in four-wheel drive or automatic mode, and travelling at a speed between 66 and 97 km/h (41 and 60 mph). A wheel-speed sensor failure will cause the electronic stability control (ESC) and anti-lock braking system (ABS) warning lights to turn on, and a "Service StabiliTrak" message to display. Safety Risk: A vehicle that suddenly pulls to one side could increase the risk of a crash. Corrective Actions: General Motors will notify owners by mail and instruct you to take your vehicle to a dealer to update the electronic-brake control module software. General Motors advises that using two-wheel-drive mode can eliminate the risk until the recall repair is completed.

  • Other#2019420

    5,327 units affected

    Issue: This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones. Note: This is a voluntary recall that is not being conducted under the requirements of the Motor Vehicle Safety Act. Safety Risk: Glass that breaks in to large pieces could create a risk of injury. Corrective Actions: The company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “DOT 287” along with the lettering “VMR” (Replacement Market) and a date code that is before July 2019. This information is printed on the bottom corner of the glass. Consumers should contact Vitro's customer service at 1-412-995-6457 or argbacklites@vitro.com to arrange for replacement of the glass.

  • Electrical#2019325

    159,474 units affected

    Issue: On certain trucks equipped with a power sliding rear window, the rear defroster circuit could overheat. This could cause melting, smoke or, in rare instances, a fire. Safety Risk: A fire could create a risk of injury. Corrective Actions: The company will notify owners by mail and advise you to take your truck to a dealer to replace the covers for the buss bar and contacts for the rear sliding window. If the rear window or sliding glass assembly are damaged due to a problem with the rear defroster, they will also be replaced.

  • Brakes#2019324

    310,121 units affected

    Issue: On certain vehicles, there could be a reduction in power brake assist due to a decrease in output from the vacuum pump. This could cause a hard brake pedal and an increase in brake pedal effort to stop the vehicle. Safety Risk: A sudden increase in brake pedal force could lead to an increase in stopping distance. This could increase the risk of a crash. Corrective Actions: The company will notify owners by mail and instruct them to take their vehicle to a dealer to reprogram the electronic brake control module.

  • Airbag#2017342

    152 units affected

    On certain vehicles, the sensing and diagnostic module (SDM), which controls airbag and pretensioner deployment, contains a software defect which may prevent the deployment of frontal airbags and pretensioners in certain circumstances. Failure of frontal airbags and seatbelt pretensioners to deploy in a crash (when warranted) could increase the risk of injury. Correction: Dealers will reflash the SDM with new software. In vehicles with any previous deployment events recorded in the SDM, the dealers will replace the existing SDM with a new SDM containing the latest software.

  • Airbag#2016439

    362,263 units affected

    On certain vehicles, the sensing and diagnostic module (SDM), which controls airbag and pretensioner deployment, contains a software defect which may prevent the deployment of frontal airbags and pretensioners in certain circumstances. Failure of frontal airbags and seatbelt pretensioners to deploy in a crash (when warranted) could increase the risk of injury. Correction: Dealers will reflash the SDM with new software. In vehicles with any previous deployment events recorded in the SDM, the dealers will replace the existing SDM with a new SDM containing the latest software. Note: This recall affects 2014-2017 model year Sierra LD/Silverado LD models and 2015-2016 model year Sierra HD/Silverado HD model vehicles.

  • Suspension#2016190

    432 units affected

    Certain vehicles may have been built with front upper control arms with a poor quality weld near the control arm’s bushing. If these welds were to fail, it could cause the upper control arm to deform or separate from the bushing, which could affect steering and directional control of the vehicle, increasing the risk of a crash causing injury and/or property damage. Correction: Dealers will replace the left and right front upper control arms, and perform a realignment.

  • Electrical#2016068

    4 units affected

    Certain vehicles may fail to conform to Canada Motor Vehicle Safety Standard (CMVSS) 114 - Theft Protection and Rollaway Protection, and CMVSS 208 - Occupant Protection In Frontal Impacts. The radio software may intermittently fail to provide an audio warning when a key is left in the ignition and the driver door is opened, or when the driver forgets to put on their seat belt, which is contrary to the requirements of the standard. A loss of the seat belt audible warning may increase the likelihood of a front outboard occupant being unbelted, increasing the risk of injury in a crash. Similarly, the loss of an audible warning when a key is left in the ignition may increase the risk of vehicle theft. Correction: Dealers will reflash the radios with corrected software.

  • Airbag#2015590

    6 units affected

    On certain vehicles, a mounting stud used to secure the airbag sensing and diagnostic module (SDM) to the vehicle may have been incorrectly positioned during the assembly process. This could stress the SDM housing and cause it to fracture which could potentially allow water to enter the SDM and cause it to malfunction. If the SDM does not perform as intended, it could increase the risk of occupant injury in the event of a crash. Correction: Dealers will send the affected vehicles to a repair facility which will relocate the mounting stud and replace the SDM.

Canadian data updated August 24, 2026

U.S. NHTSA recalls

05
  • AIR BAGS:SIDE/WINDOW:CURTAIN:INFLATOR#21V504000

    General Motors LLC (GM) is recalling certain 2015-2016 GMC Sierra 1500, 2500, 3500, and Chevrolet Silverado 1500, 2500, and 3500 trucks. The roof-rail air bag (RRAB) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.

    Risk: A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.

    Remedy: Dealers will replace the left and right side RRAB modules, free of charge. Interim owner notification letters informing owners of the safety risk were mailed on August 18, 2021. Owners will receive a second notice when the remedy is available. Phase I owner notification letters were mailed on May 5, 2022. Phase II owner notification letters are expected to be mailed on May 31, 2022. Owners may contact GMC customer service at 1-888-988-7267 or Chevrolet customer service at 1-800-222-1020. This recall supersedes NHTSA recall number 20V-736. GM's number for this recall is N202324251.

  • SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES#18V578000

    General Motors LLC (GM) is recalling certain 2015-2016 Chevrolet Silverado 2500, 3500, 1500 Crew Cab Special Service, Tahoe Police Pursuit/Special Service, GMC Sierra 2500, and 3500 vehicles. The brake pedal pivot nut may loosen, causing the brake pedal to be loose or inoperative.

    Risk: If the brake pedal becomes loose or inoperative, the driver may be unable to stop the vehicle by using the brake pedal. Additionally, a loose pedal may also interfere with the accelerator pedal. Either condition may increase the risk of a crash.

    Remedy: GM will notify owners, and dealers will add adhesive to the nut and reinstall the nut with increased tightness, free of charge. The recall began October 3, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 18278. Note: The vehicles in this recall need this additional remedy despite being covered by recall 16V069 for brake pedal loosening.

  • AIR BAGS:FRONTAL#17V437000

    General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.

    Risk: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.

    Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.

  • AIR BAGS:FRONTAL#16V651000

    General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.

    Risk: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.

    Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.

  • SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES#16V069000

    General Motors LLC (GM) is recalling certain model year 2015-2016 Chevrolet Silverado 1500, 2500, and 3500 heavy duty trucks manufactured October 1, 2013, to February 1, 2016, 2015-2016 Chevrolet Tahoe Police Pursuit Vehicles (PPV) manufactured March 1, 2014, to February 1, 2016, and 2015-2016 GMC Sierra 2500 and 3500 heavy duty trucks manufactured October 29, 2013, to February 1, 2016. On the affected vehicles, the brake pedal pivot nut may loosen, causing the brake pedal to be loose or inoperative.

    Risk: If the brake pedal becomes loose or inoperative, the driver may be unable to stop the vehicle by using the brake pedal. Additionally, a loose pedal may also interfere with the accelerator pedal. Either condition may increase the risk of a crash.

    Remedy: GM will notify owners, and dealers will add adhesive to the brake pedal pivot nut and reinstall with an increased torque, free of charge. The recall began on March 14, 2016. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 20760.

Does this recall apply to my vehicle?

Matched by make, model, and model year. Many recalls affect only specific VIN ranges — confirm with your dealer using your full VIN.

What to do

Recall repairs are free at a franchised dealer in both countries. To confirm a recall applies to your specific vehicle, or to book the work, contact your manufacturer or dealer with your full VIN, or use the official channel:

Check a 2016 GMC Sierra 2500 VIN

A VIN decode confirms your vehicle's exact model year, trim and assembly plant, then runs this same recall check against it.

Data sources and coverage limits